Westinghouse Treebridge Station Five-Light Indoor Chandelier 6224000 Manual De Instruções
4
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (see fig. 1).
3. Thread hex nut (D) onto mounting nipple (E) approximately 1/4 inch and insert lock washer
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (see fig. 1).
3. Thread hex nut (D) onto mounting nipple (E) approximately 1/4 inch and insert lock washer
(F), then thread mounting nipple (E) onto mounting bar (A) and secure with hex nut (D).
4. Spread fixture arms (G) to an equal distance apart.
5. Align pins (H) on fixture ring (I) with corresponding pin holes (J) on each fixture arm (G)
5. Align pins (H) on fixture ring (I) with corresponding pin holes (J) on each fixture arm (G)
then snap pins (H) into pin holes (J) until fixture ring (I) is secure.
NOTE: To avoid scratching fixture surface, carefully align pins (H) before snapping into pin holes (J).
6. Secure fixture loop (K) to nipple (L).
7. Open one link on bottom end of chain (M). Attach to fixture loop (K). Securely close link on
7. Open one link on bottom end of chain (M). Attach to fixture loop (K). Securely close link on
chain (M).
8. Thread screw collar ring (N) onto screw collar (O), then place canopy (P) over top of screw
collar (O).
9. Lace wires up through every other link on chain (M) then up through screw collar (O) and
mounting nipple (E).
10. Open one link on top end of chain (M). Attach to loop on screw collar (O). Securely close
link on chain (M).
11. Identify color coding of fixture wires (see fig. 2).
12. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
12. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
black outlet box wire. Do not twist wires.
13. Fit wire connector (Q from fig. 1) over wires and twist until there is a firm connection. If
wire connector (Q) easily comes off, reattach and check again for a firm connection.
14. Repeat steps 12 and 13 with the white (group B from fig. 2) fixture wires and outlet box wires.
15. Partially thread green grounding screw (R) into side hole (S) on mounting bar (A) (see fig. 1).
16. Wrap ground wire from fixture around green grounding screw (R) leaving enough excess
16. Wrap ground wire from fixture around green grounding screw (R) leaving enough excess
wire to then connect ground wire and outlet box wire with wire connector (Q), if applicable.
17. Tighten green grounding screw (R). Do not over tighten.
18. Remove screw collar ring (N) from screw collar (O) and secure screw collar (O) to mounting
18. Remove screw collar ring (N) from screw collar (O) and secure screw collar (O) to mounting
nipple (E).
19. Tuck wires inside outlet box (B).
20. Raise canopy (P) to ceiling and secure screw collar ring (N) to screw collar (O).
MOUNTING AND WIRING INSTRUCTIONS
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Place glass shades (T) and plates (U) over sockets (V) and secure with retaining rings (W).
2. Install lamp(s). Do not exceed recommended wattage.
3. Turn power back on at circuit box.
2. Install lamp(s). Do not exceed recommended wattage.
3. Turn power back on at circuit box.
12 pg_W-153_EFS 11/12/04 10:35 AM Page 4