Royal Consumer Information Products Super Hot Toater Manual Do Utilizador
'(6&5,37,21
The Super Hot Toaster has a single aerated burner, the design of which produces two parallel ribbons of flame
which run across the front of the fire bed. The rear ribbon of flame is ignited first and the front ribbon cross-lights
from it instantaneously. A single gas control selects ignition (pilot only) and can be turned anticlockwise to select
a high rate and then a reduced input at the maximum rotation. For extra safety the control is designed so that gas
cannot be allowed to reach the burner until pilot ignition has been proven. A separate push button piezo igniter
provides pilot ignition.
The Super Hot Toaster has a single aerated burner, the design of which produces two parallel ribbons of flame
which run across the front of the fire bed. The rear ribbon of flame is ignited first and the front ribbon cross-lights
from it instantaneously. A single gas control selects ignition (pilot only) and can be turned anticlockwise to select
a high rate and then a reduced input at the maximum rotation. For extra safety the control is designed so that gas
cannot be allowed to reach the burner until pilot ignition has been proven. A separate push button piezo igniter
provides pilot ignition.
A Flame Supervision Device (FSD) is fitted. This ensures that if the pilot goes out for any reason (including being
turned off), the gas flow to the burner is cut off until the full lighting procedure is repeated. The oxy-pilot or
O.D.S. will cause the appliance to ‘shut off’ in the event of continued spillage occurring under hazardous or
blocked flue conditions. The burner assembly is fixed to the base of the radiant box which also includes a fire back
made of ceramic fibre, this forms an insulating surface to reflect heat into the fire bed, raising its temperature and
increasing the amount of heat radiated into the room. A decorative brass trim completes the front face of the
appliance.
turned off), the gas flow to the burner is cut off until the full lighting procedure is repeated. The oxy-pilot or
O.D.S. will cause the appliance to ‘shut off’ in the event of continued spillage occurring under hazardous or
blocked flue conditions. The burner assembly is fixed to the base of the radiant box which also includes a fire back
made of ceramic fibre, this forms an insulating surface to reflect heat into the fire bed, raising its temperature and
increasing the amount of heat radiated into the room. A decorative brass trim completes the front face of the
appliance.
There are two types of front and fret available for this appliance; these have perforated frets to allow air to be
entrained into the fire bed to ensure clean combustion. The optional fire fronts and frets are listed in figure 11. If
other Fronts and Frets are to be used they must have a minimum open area in the fret of 20 square centimetres and
60 square centimetres in the Front, as shown in figure 11.
entrained into the fire bed to ensure clean combustion. The optional fire fronts and frets are listed in figure 11. If
other Fronts and Frets are to be used they must have a minimum open area in the fret of 20 square centimetres and
60 square centimetres in the Front, as shown in figure 11.
A flame adjustment lever is fitted to allow a longer softer flame to be used to enhance the appearance of the
firebed; this can be operated in either the high or low position via the control lever on the front fascia panel.
firebed; this can be operated in either the high or low position via the control lever on the front fascia panel.
,03257$17127(6
The Super Hot Toaster is a decorative fuel effect appliance designed and manufactured to the requirements of
the British Standards Institution BS 5258 Part 12: 1990 and is for use on Natural Gas only
The Super Hot Toaster is a decorative fuel effect appliance designed and manufactured to the requirements of
the British Standards Institution BS 5258 Part 12: 1990 and is for use on Natural Gas only
.
All gas appliance installations must be installed by a competent person in accordance with the current Gas
Safety (Installation and Use) Regulations 1994 (as amended) or the rules in force and in accordance with the
attached Installation Instructions, failure to do so could lead to prosecution.
Safety (Installation and Use) Regulations 1994 (as amended) or the rules in force and in accordance with the
attached Installation Instructions, failure to do so could lead to prosecution.
Areas of this appliance will become hot after prolonged running and it is recommended that for the protection of
the very young, elderly and infirm a fireguard conforming to BS 6539 or BS 6778 be used.
the very young, elderly and infirm a fireguard conforming to BS 6539 or BS 6778 be used.
Care should be taken to prevent any damage being caused to surrounding soft furnishings or decor e.g. many
embossed vinyl wall coverings may become discoloured if located too close to the appliance. Clearances required
for combustible shelves are shown on page 3.
embossed vinyl wall coverings may become discoloured if located too close to the appliance. Clearances required
for combustible shelves are shown on page 3.
It is recommended that the chimney or flue should be swept annually by a competent person and the appliance
checked for spillage (smoke test) and that there are no excessive deposits of soot.
checked for spillage (smoke test) and that there are no excessive deposits of soot.
The curing effect of heating the coals will cause an initial odour which, although not harmful, may require
additional ventilation until the odour has disappeared. This appliance will run on Full for approximately 4.4
hours on one therm of gas.
additional ventilation until the odour has disappeared. This appliance will run on Full for approximately 4.4
hours on one therm of gas.
This product uses fuel effect pieces, gaskets and insulation material containing Refractory Ceramic Fibre
(RCF), which are man-made vitreous silicate fibres. Excessive exposure to these materials may cause temporary
irritation to eyes, skin and respiratory tract, consequently, it makes sense to take care when handling these
articles to ensure that the release of dust is kept to a minimum.
(RCF), which are man-made vitreous silicate fibres. Excessive exposure to these materials may cause temporary
irritation to eyes, skin and respiratory tract, consequently, it makes sense to take care when handling these
articles to ensure that the release of dust is kept to a minimum.
72/,*+77+($33/,$1&(
1.
Remove the fret (controls cover), to gain access to the controls
2.
Press and turn the gas control until the indicator mark is opposite to IGN. Keep the control fully depressed.
Press and release the ignition button. Check that the pilot flame has lit at all ports. Keep the gas control
depressed for a further 20 seconds. Release the gas control and check the pilot remains alight.
Press and release the ignition button. Check that the pilot flame has lit at all ports. Keep the gas control
depressed for a further 20 seconds. Release the gas control and check the pilot remains alight.
3.
Depress the gas control slightly and turn fully anticlockwise until the indicator mark is opposite the small
flame symbol. The burner will now ignite from the pilot assembly and run at the low rate.
flame symbol. The burner will now ignite from the pilot assembly and run at the low rate.
Page 2