Yaesu FT-450D Manual Do Utilizador
Page 68
FT-450D O
PERATION
M
ANUAL
P
ROGRAMMABLE
M
EMORY
S
CANNING
(PMS)
To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable
Memory Scanning (PMS) feature, which utilizes two special-purpose memory pairs (“MEM-P1L/MEM-P1U” and
“MEM-P2L/MEM-P2U”). The PMS feature is especially useful in helping you to observe any operating sub-band
limits, which apply to your Amateur license class.
Memory Scanning (PMS) feature, which utilizes two special-purpose memory pairs (“MEM-P1L/MEM-P1U” and
“MEM-P2L/MEM-P2U”). The PMS feature is especially useful in helping you to observe any operating sub-band
limits, which apply to your Amateur license class.
1. Store the Lower and Upper tuning/scanning limit
frequencies into the memory pair “MEM-P1L” and
“MEM-P1U”, respectively, or “MEM-P2L” and
“MEM-P2U”. See page 58 for details regarding
memory storage.
“MEM-P1U”, respectively, or “MEM-P2L” and
“MEM-P2U”. See page 58 for details regarding
memory storage.
2. Press the [F] button, followed by the [SCAN/PMS]
button.
3. Rotate the [DSP/SEL] knob to select “PMS-1”
“PMS2” or “PMS1+2”.
PMS-1
PMS-1
:
The scanner will be limited within the
frequency range programmed in the
memory pair “MEM-P1L/MEM-P1U”.
frequency range programmed in the
memory pair “MEM-P1L/MEM-P1U”.
PMS-2
:
The scanner will be limited within the
frequency range programmed in the
memory pair “MEM-P2L/MEM-P2U”.
frequency range programmed in the
memory pair “MEM-P2L/MEM-P2U”.
PMS-1+2
: The scanner will be limited within the
frequency ranges programmed by both
memory pairs (“MEM-P1L/MEM-P1U”
and “MEM-P2L/MEM-P2U”).
memory pairs (“MEM-P1L/MEM-P1U”
and “MEM-P2L/MEM-P2U”).
If a memory pair is vacant, the PMS-1+2 selec-
tion is not available.
tion is not available.
4. Press the [SCAN/PMS] button.
5. Rotate the [SQL/RF GAIN] knob just to the point
5. Rotate the [SQL/RF GAIN] knob just to the point
where the noise is silenced and the “
” indi-
cator on the display turns off.
6. Press the [SCAN/PMS] key to initiate upward
scanning (toward higher frequencies or higher
memory channel numbers).
memory channel numbers).
7. If you want to change direction of the scan while it
is underway, rotate the [MAIN DIAL] knob one click
in the opposite direction (in this case, one click
counter-clockwise). You will see the scanner re-
verse direction and scan down in frequency.
You may change the direction of the scanner by
pressing and holding the microphone’s [UP]/
[DWN] key for one second, if you are using the
MH-31
in the opposite direction (in this case, one click
counter-clockwise). You will see the scanner re-
verse direction and scan down in frequency.
You may change the direction of the scanner by
pressing and holding the microphone’s [UP]/
[DWN] key for one second, if you are using the
MH-31
A8J
Hand Microphone or optional MD-
100
A8X
Desktop Microphone.
8. In FM/AM mode, when the scanner encounters a
signal strong enough to open the squelch, the
scanner will halt for five seconds, after which scan-
ning will resume.
In the SSB/CW and SSB-based Data modes,
when the scanner encounters a signal strong
enough to open the squelch, the scanner will step
across the signal very slowly, giving you time to
stop the scan, if you like.
scanner will halt for five seconds, after which scan-
ning will resume.
In the SSB/CW and SSB-based Data modes,
when the scanner encounters a signal strong
enough to open the squelch, the scanner will step
across the signal very slowly, giving you time to
stop the scan, if you like.
A
DVICE
:
You may select the manner in which the scanner re-
sumes while it has paused on a signal, using Menu
Item “SCN RES” The default “5Sec” setting will cause
the scanner to resume scanning after five seconds;
you may change it, however, to resume only after the
carrier has dropped out, if you like See page 85.
sumes while it has paused on a signal, using Menu
Item “SCN RES” The default “5Sec” setting will cause
the scanner to resume scanning after five seconds;
you may change it, however, to resume only after the
carrier has dropped out, if you like See page 85.
[DSP/SEL] Knob
[SCAN/PMS] button
[SQL/RF GAIN] Knob
[MAIN DIAL] Knob
[F] button