Yamaha SP2060 V1.2 Manual Do Proprietário
Ref
erences
Intr
oduction
to the SP2060
Fore
w
o
rd
The Contr
ols
and Connector
s
Netw
ork Settings
P
anel Operation
Panel Operation
SP2060 Owner’s Manual
25
DELAY
You can set the signal delay time on each input and output
channel. Set the On/Off parameter to On to delay the signal,
and Off to bypass the delay.
channel. Set the On/Off parameter to On to delay the signal,
and Off to bypass the delay.
1.
Press the [DELAY] key to select the Delay
display.
display.
2.
Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
Pressing the [SEL] keys for Input channels A and B si-
multaneously will turn on the [SEL] key LEDs and select
channel SUM.
and the corresponding channel name is displayed.
Pressing the [SEL] keys for Input channels A and B si-
multaneously will turn on the [SEL] key LEDs and select
channel SUM.
3.
Press the [
▲INC]/[▼DEC] keys to select On or
Off.
4.
Press the [DELAY] or [NEXT] key to display
the Time parameter.
the Time parameter.
5.
Press the [
▲INC]/[▼DEC] keys to adjust the
delay time.
EQ (Equalizer)
An EQ boosts or cuts the level of specified frequency ranges.
The SP2060’s internal EQ processes input and output sig-
nals.
The SP2060’s internal EQ processes input and output sig-
nals.
Input EQ
You can apply eight-band EQ to Input channels A, B, and
SUM.
Set the On/Off parameter to On to apply EQ to the signal,
and Off to not process the signal.
SUM.
Set the On/Off parameter to On to apply EQ to the signal,
and Off to not process the signal.
You can set the following parameters for each band.
You can select a type of filter for band 1 and band 8. All other
bands utilize a fixed parametric EQ.
bands utilize a fixed parametric EQ.
• PEQ
This is a standard parametric equalizer.
• L.SHELF(Low Shelving)
Does not cut the lower frequency range, but cuts starting
from the vicinity of the cutoff frequency toward the higher
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
from the vicinity of the cutoff frequency toward the higher
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
• H.SHELF(High Shelving)
Does not cut the higher frequency range, but cuts starting
from the vicinity of the cutoff frequency toward the lower
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
from the vicinity of the cutoff frequency toward the lower
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
• HPF
This is a high pass filter (Q=0.7). The low frequency range
is mildly cut (12dB/Oct), creating a slow curve.
is mildly cut (12dB/Oct), creating a slow curve.
• LPF
This is a low pass filter (Q=0.7). The high frequency range
is mildly cut (12dB/Oct), creating a slow curve.
is mildly cut (12dB/Oct), creating a slow curve.
Parameter
Range
INPUT A/B/SUM
0–1300.00msec
OUTPUT 1-6
0–500.00msec
NOTE
Channel SUM is a new channel created by applying the Level and
Mute settings to Input channel A and B respectively, then adding
both channel values.
Mute settings to Input channel A and B respectively, then adding
both channel values.
IN A
ON/OFF = OFF
ON/OFF = OFF
IN SUM
ON/OFF = OFF
ON/OFF = OFF
IN SUM
ON/OFF = ON
ON/OFF = ON
IN B
TIME = 130.00ms
TIME = 130.00ms
IN B
TIME = 120.00ms
TIME = 120.00ms
Parameter
Range
Function
BYPASS
ON/OFF
Sets the bypass for
each frequency range
to On or Off.
each frequency range
to On or Off.
Q
16.0–0.1
Specifies the width of
each frequency range.
each frequency range.
FREQ
(Frequency)
(Frequency)
20.0Hz–20.0kHz
Specifies the center
frequency of each
frequency range.
frequency of each
frequency range.
GAIN
–18dB through
+18.00dB
+18.00dB
Sets the gain of the
target frequency.
target frequency.
Parameter
Range
Function
TYPE
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
Selects a type of filter.