Shakespeare Electronic 410-R Folheto
Style 410-R
Thank you for purchasing a Shakespeare antenna product.
Customer comments are welcome. Before installing, please study
the diagram and check parts supplied against those listed.
IMPORTANT! Please read all instructions
before installing.
The Style 410-R Mounting Kit is a versatile antenna mounting
kit comprised of a Shakespeare Style 81-S Swivel Mount and a
Shakespeare Style 408-R Standoff Bracket. The dual swivel mount
permits mounting on vertical or horizontal surfaces. For use with
1½” antennas, and antennas of 1
1
/
8
” and 1” diameter by using the
appropriate adapter (supplied) in the standoff bracket.
Tools required: Drill and drill bit for ¼” screws;
screwdriver; wrench or pliers
Installation Instructions
Choose an antenna mounting location that is as high as feasible,
as free as possible from obstructions, and as far as possible from
other antennas and strong sources of RF.
1. Using the base of the Swivel Mount as a template, mark the
location for the four mounting holes. Drill ¼” holes.
Note: When drilling fiberglass, place a wooden backup block
behind the surface if possible, to minimize push-through
damage.
2. Attach the Swivel Mount to the mounting surface using
hardware (sold separately) that is applicable to the mounting
surface.
IMPORTANT: If the thickness of the mounting
surface is not adequate to support the antenna under
expected stress, a wooden back-up pad (not supplied)
should be applied underneath the mounting surface
during installation.
3. Assemble the antenna to the Swivel Mount, being careful not to
damage the antenna’s cabling, if any.
4. Loosen the wing nut on top of the Standoff Bracket and slide
the retainer bar out of the way. Gently place the antenna in its
mounting position in the U-shaped opening in the bracket. For
1
1
/
8
” and 1” antennas, put the appropriate reducing adapter
(supplied) in the opening.
5. Rotate the retainer bar over the antenna to lock it in place.
6. Using the Standoff Bracket itself as a template, mark the position
6. Using the Standoff Bracket itself as a template, mark the position
for its mounting holes.
7. Drill ¼” mounting holes, and install the bracket using stainless
steel hardware appropriate to the mounting surface (hardware
sold separately).
8. Tighten the wing nut to secure the antenna in the bracket. The
completed installation should attach the antenna firmly to the
mounting surface, leaving no “play” between the antenna and
the standoff bracket.
©2002 Shakespeare Co. · Form I-410-R J: rev. 04/25/2010
* Not supplied. For some types of mounting surfaces you might need
stainless steel woodscrews or other hardware.
Wing Nut
Retainer Bar
Lockwasher*
Standoff Bracket
Assembly
Mounting
Screw*
Washer*
Nut*
Reducing Adapter
Antenna
STANDOFF
BRACKET
SWIVEL
MOUNT
Supplied Parts
1 Swivel Mount assembly
1 Standoff Bracket assembly
1 1“ Reducing adapter
1 1
1 Standoff Bracket assembly
1 1“ Reducing adapter
1 1
1
/
8
“ Reducing Adapter
35
-9
0-1
127
-0
0
Shakespeare Electronic Products Group
U.S. Operations: 6111 Shakespeare Rd. · Columbia, SC 29223 · 803-227-1590 · Fax: 803-419-3099 · www.shakespeare-marine.com
U.K. Operations: Enterprise Way, Fleetwood, Lancashire, FY7
8RY, England · +44 (0) 1253 858787 · Fax: +44 (0) 1253-859595 · www.vtronix-antennas.com
Shakespeare is a subsidiary of Jarden Corporation (NYSE: JAH)
1”-14 Thread
Mount Base
Mounting Screw*
Lockwasher*
Nut*
Swivel