Thule PR350 B V350 Manual Do Utilizador
___________________________________________________________________________
page 20
6.9 Return to factory setting
Each setting in the configuration menu will be stored even if the power is removed.
However, if your entire set-up doesn’t work well, it may be desirable to reload the
original factory settings.
If this option is selected by the ”
Each setting in the configuration menu will be stored even if the power is removed.
However, if your entire set-up doesn’t work well, it may be desirable to reload the
original factory settings.
If this option is selected by the ”
⇒” key, the user will be asked SURE ? in the
display. If accepted, the user must push the “ENTER” key. Otherwise cancel by
pushing “
pushing “
⇐” or “>VOL”.
Please notice that delay and volume trim settings will be returned to their original
settings with this command.
settings with this command.
6.10 OSD
The information on the front panel display can also be displayed on the TV-set or
Projector (On Screen Display), by the built-in video encoder.
When entering the config menu, a full screen OSD is enabled, which overrides other
video sources.
In normal mode the OSD is mixed with the selected video signal.
The following settings are possible:
- OSD is disabled
- OSD is enabled only by commands from the remote control (factory setting)
- OSD is enabled both by command from the remote control and front panel keys
When no OSD is displayed, the OSD circuit is automatically switched out of the
video signal path to obtain full bandwidth of 70 MHz for maximum video quality.
The information on the front panel display can also be displayed on the TV-set or
Projector (On Screen Display), by the built-in video encoder.
When entering the config menu, a full screen OSD is enabled, which overrides other
video sources.
In normal mode the OSD is mixed with the selected video signal.
The following settings are possible:
- OSD is disabled
- OSD is enabled only by commands from the remote control (factory setting)
- OSD is enabled both by command from the remote control and front panel keys
When no OSD is displayed, the OSD circuit is automatically switched out of the
video signal path to obtain full bandwidth of 70 MHz for maximum video quality.
6.11 SPDIF OUT
In this menu you can select what channels should be send to the optical digital
output.
The sample rate will change with different sources, e.g. analog input and DTS
96kHz will output 96kHz, while normal DVD is 48kHz.
The receiver should be able to handle the different sample rates.
In this menu you can select what channels should be send to the optical digital
output.
The sample rate will change with different sources, e.g. analog input and DTS
96kHz will output 96kHz, while normal DVD is 48kHz.
The receiver should be able to handle the different sample rates.
6.12 Power Amp control
The PR350B can control an external Thule Audio amplifier via the rear RJ45
connector i.e. Space PA350B. When using IA350, PA350 or PA250 MKII for L & R
power amplification (see “Side Channels” in “Surround mode” section), the PR350B
should be set in “FIXED 2 CH CONTROL”. In normal set-up in a 5-7.1 system, the
PR350B should be set in “2 CH AND 5 CH CONTROL”.
6.13 ProLogic II
In this menu it is possible to select the default setting of ProLogic II for each input.
You can choose between movie and music mode, depending on what type of
material is commonly used.
The PR350B can control an external Thule Audio amplifier via the rear RJ45
connector i.e. Space PA350B. When using IA350, PA350 or PA250 MKII for L & R
power amplification (see “Side Channels” in “Surround mode” section), the PR350B
should be set in “FIXED 2 CH CONTROL”. In normal set-up in a 5-7.1 system, the
PR350B should be set in “2 CH AND 5 CH CONTROL”.
6.13 ProLogic II
In this menu it is possible to select the default setting of ProLogic II for each input.
You can choose between movie and music mode, depending on what type of
material is commonly used.