Kenwood TK-260G Manual Do Utilizador
TK-260G/270G
21
CIRCUIT DESCRIPTION/SEMICONDUCTOR DATA
Fig. 10 Control system
8. CONTROL SYSTEM
Keys and channel selector circuit.
The signal from the keys and channel selector are directly
The signal from the keys and channel selector are directly
input to the microprocessor, as shown in fig. 10.
SEMICONDUCTOR DATA
LCD Driver : LC75823W (Display UNIT IC501)
(TK-270G only)
■
Block diagram
LATCH & DRIVER
SHIFT REGISTER
COMMON
DRIVER
ADDRESS
DETECTOR
CLOCK
GENERATOR
V
DD
CE
CL
DI
V
SS
OSC
INH
V
DD
2
V
DD
1
COM1 COM2 COM3
S52 S51
S1
Pin No.
Name
I/O
Active
Function
1-52 S1-S52
O
-
Segment output for displaying data
transferred form serial data.
transferred form serial data.
53-55 COM1-COM3
O
-
Common drive output.
Frame frequency fo=(fosc/384)Hz
Frame frequency fo=(fosc/384)Hz
56
VDD
-
-
The display to turn off
57
INH
I
L
INT=L : Turn off
INT=H : Turn on
Apply 2/3 the LCD drive bias voltage
INT=H : Turn on
Apply 2/3 the LCD drive bias voltage
58
VDD1
I
-
from outside. If 1/2 the bias is applied,
connect to VDD2.
Apply 1/3 the LCD drive bias voltage
connect to VDD2.
Apply 1/3 the LCD drive bias voltage
59
VDD2
I
-
from outside. If 1/2 the bias is applied,
connect to VDD1.
connect to VDD1.
■
Pin function
60
VSS
-
-
61
OSC
I/O
-
Oscillation terminal
62
CE
I
H
Chip enable. Serial data transfer terminal.
Connected to the microprocessor.
Connected to the microprocessor.
63
CL
I
Synchronizing clock. Serial data transfer terminal.
Connected to the microprocessor.
Connected to the microprocessor.
64
DI
I
-
Trnsfer data. Serial data transfer terminal.
Connected to the microprocessor.
Connected to the microprocessor.
Pin No.
Name
I/O
Active
Function
UPB1509GV (IC301)
■
Pin connection diagram
1
2
3
4
5
6
7
8
D
Q
Q
CLK
D
Q
Q
CLK
D
Q
Q
CLK
OUT
IN
IN
SW1
SW2
Pin No.
Pin Name
1
V
CC1
2
IN
3
IN
4
GND
5
SW1
6
SW2
7
OUT
8
V
CC2
■
Block diagram
Pin
Pin Applied Pin
Functions and uses
No. name voltage voltage
1 V
CC1
2.2-2.5
-
Power supply voltage pin for the input amplifier section and
division circuit. Connect a bypass capacitor to this pin to reduce
the high-frequency impedance with the ground (for example, 1000 pF).
division circuit. Connect a bypass capacitor to this pin to reduce
the high-frequency impedance with the ground (for example, 1000 pF).
2 IN
-
1.7-4.95 Signal input pin. Connect a coupling capacitor to this pin for
DC cutting with an external circuit (for example, 1000 pF).
3 IN
-
1.7-4.95 Input signal bypass pin. Connect a bypass capacitor to this
pin to reduce the high-frequency impedance with the ground
(for example, 1000 pF).
(for example, 1000 pF).
4 GND
0
-
Ground pin. Connect it with the ground pattern. The ground
pattern on the PC board should be wide enough to minimize
impedance.
pattern on the PC board should be wide enough to minimize
impedance.
5 SW1
H/L
-
Division ratio setting pin. The division ratio can be set by the
following voltage:
following voltage:
6 SW2
Connect a bypass capacitor to this pin to reduce the high-
frequency impedance with the ground.
frequency impedance with the ground.
7 OUT
-
1.0-4.7 Division signal output pin. Emitter follower output. 0.1 Vpf or
more can be output under 200-ohmload. Connect a coupling
capacitor to this pin for DC cutting with an external circuit
(for example,1000 pF).
capacitor to this pin for DC cutting with an external circuit
(for example,1000 pF).
8 V
CC2
2.2-5.5
-
Power supply voltage pin for the output buffer circuit. Connect
a bypass capacitor to this pin to reduce the high-frequency
impedance with the ground (for example, 1000 pF).
a bypass capacitor to this pin to reduce the high-frequency
impedance with the ground (for example, 1000 pF).
SW2
H
L
SW1
H
1/2
1/4
L
1/4
1/2
■
Pin Fanction
Channel selector
IC13
-COM
CN501
CN1
TK-270G
TK-260G
EN1
87
3
25
EN3
EN2
KOUT0
KOUT1
KOUT2
KOUT3
KIN0
KIN1
KIN2
KIN3
KIN4
16
27
KEYAD
PTT
MONI
SW
LAMP
SW
PTT
SW
1
2
3
A
4
5
6
B
7
8
9
C
∗
0
#
D
5M
47k
47k
100k