John Deere HR-BG5002 Manual Do Utilizador

Operator’s Manual   

 

 

 

 

 

       

             

at once. dO nOT use the  

    

 

 

 

 

 

 

 

 

 

appliance until leak is sealed. 

 

Leak detected at cylinder, regulator or  Regulator fitting loose.   

 

Tighten fitting and “Leak Test”.

other connections. 

 

 

    

 

 

 

 

Gas leak in hose/regulator or control 

See authorized service center.

    

 

 

 

 

valves.

Flame flashback beneath control panel.  Venturi blocked.  

 

 

Remove burner, clean ventrui.    

    

 

 

 

 

 

 

 

 

 

See “Venturi Tube”.

Burner will not light. 

 

 

Out of LP-Gas.   

 

 

Refill LP-Gas Cylinder.

    

 

 

 

 

Ignitor wire(s) not connected.   

Connect both main burner and    

    

 

 

 

 

 

 

 

 

 

side burner electrode wires.

    

 

 

 

 

Ignitor electrode misaligned on burner.  Realign electrodes.

    

 

 

 

 

Ignitor malfunction. 

 

 

Use “Manual Lighting” procedures.

    

 

 

 

 

Regulator is not fully connected to the   Tighten the regulator hand-wheel.

    

 

 

 

 

cylinder valve.   

 

    

 

 

 

 

Burner valve left open while cylinder  

Close burner and cylinder valves.

    

 

 

 

 

valve was opened causing excess  

Open cylinder valve slowly, then

    

 

 

 

 

flow device to activate.   

 

open burner valve to light.

    

 

 

 

 

A leak in the system causing the  

Leak test connections to  

    

 

 

 

 

excess flow device to activate.   

determine loose fitting. Tighten    

    

 

 

 

 

 

 

 

 

 

fitting. Leak test system.

    

 

 

 

 

Venturi blocked.  

 

 

Remove burner, clean venturi See  

    

 

 

 

 

 

 

 

 

 

“Venturi Tubes”.

    

 

 

 

 

Venturi not aligned with valve orifice. 

Realign venturi to orifice. See 

    

 

 

 

 

 

 

 

 

 

“Venturi Tubes”.

    

 

 

 

 

Orifice blocked.  

 

 

Remove burner, clean orifice with  

    

 

 

 

 

 

 

 

 

 

a pin or fine wire. Do not attempt  

    

 

 

 

 

 

 

 

 

 

to drill orifice.

    

 

 

 

 

Hose is twisted.  

 

 

Straighten hose. Keep away from  

    

 

 

 

 

 

 

 

 

 

bottom casting.

Decreasing heat, “popping sound”. 

Out of LP-Gas.   

 

 

Refill LP-Gas Cylinder.

  

    

 

 

 

 

Venturi blocked.  

 

 

Remove burner, clean venturi.    

    

 

 

 

 

 

 

 

 

 

See “Venturi Tubes”.

Hot spots on cooking surface.   

Venturi blocked.  

 

 

Remove burner, clean venturi.    

    

 

 

 

 

 

 

 

 

 

See “Venturi Tubes”