JobSite Systems A45-X2 Manual Do Utilizador
6
Level Adjustment Screws
The front panel level adjustment screws
allow you to adjust the level of the A45-X2,
relative to other amplifiers in your system.
Use a 1/8" slotted screwdriver to adjust the
screws. If the A45-X2 is the only amplifier in
your system, leave the screws at their
factory default position (turned fully
clockwise).
allow you to adjust the level of the A45-X2,
relative to other amplifiers in your system.
Use a 1/8" slotted screwdriver to adjust the
screws. If the A45-X2 is the only amplifier in
your system, leave the screws at their
factory default position (turned fully
clockwise).
TROUBLESHOOTING
No sound on one channel
You could have a short circuit or loose wire
at the speaker or amplifier terminals. Check
that the connections are secure and that
there are no loose strands of wire crossing
from the positive to the negative terminals
at the back of the amplifier and/or the
speaker.
at the speaker or amplifier terminals. Check
that the connections are secure and that
there are no loose strands of wire crossing
from the positive to the negative terminals
at the back of the amplifier and/or the
speaker.
Short circuit or a break in the speaker wire.
Disconnect the speaker wire at both ends,
separate the 2 conductors at both ends and
test with a meter for a short circuit. If there
is no short, connect the two conductors at
one end and test with a meter for continuity.
Disconnect the speaker wire at both ends,
separate the 2 conductors at both ends and
test with a meter for a short circuit. If there
is no short, connect the two conductors at
one end and test with a meter for continuity.
Speaker is not working
Connect the speaker to a channel that plays
another speaker.
another speaker.
Audio cable to input is bad
Connect another cable that is known
to be good.
to be good.
No sound on both channels
Audio cable to the main inputs is bad.
Connect another cable that is known
to be good.
Connect another cable that is known
to be good.
Active LED ON or OFF
Check trigger mode 12V trigger voltage.
Hum from the speakers
Hum may be caused by a ground loop
between two of the other components in
the system. To test for a ground loop, try
reversing the ac plugs of each of the
components in the system. Check for
faulty cables, faulty source material, an
ungrounded phono system or a
defective component.
between two of the other components in
the system. To test for a ground loop, try
reversing the ac plugs of each of the
components in the system. Check for
faulty cables, faulty source material, an
ungrounded phono system or a
defective component.
Amp will not turn on
AC power cord must be plugged into a
working outlet.
working outlet.
Master power switch must be on. 12V
trigger must be present.
trigger must be present.
Bass sound is weak and the
stereo image is “phasey” or
“blurry” sounding in one room
stereo image is “phasey” or
“blurry” sounding in one room
The loudspeakers are wired out of phase.
Reverse the connections at the back of
one speaker.
Reverse the connections at the back of
one speaker.
SPECIFICATIONS
Power handing:
45 watts x 2
45 watts x 2
Frequency response:
10 Hz to 100 kHz +/- 3dB
10 Hz to 100 kHz +/- 3dB
Signal noise ratio:
>= 85dB
Power supply
AC120V, 60 Hz
AC120V, 60 Hz
Power consumption
200 watts
200 watts
Dimensions:
17" wide x 2-5/16" high (including feet)
x 13-1/8" deep
17" wide x 2-5/16" high (including feet)
x 13-1/8" deep
Warranty: 2 year limited
DS00374BMY_A45-X2.qxp 6/8/05 4:20 PM Page 6