Lenmar Enterprises OmniSource Digital Camera Batteries Folheto
OmniSource
®
Li-Ion
Universal Charger for Li-Ion Camcorder &
Digital Camera Batteries
Digital Camera Batteries
PLEASE READ THE INFORMATION AND FOLLOW ALL
INSTRUCTIONS THOROUGHLY BEFORE USING THIS
PRODUCT.
INSTRUCTIONS THOROUGHLY BEFORE USING THIS
PRODUCT.
Introduction
The OmniSource Lithium-Ion (Li-Ion) is a fully automatic
camcorder battery charger which is compatible with virtually all 3.6
volt and 7.4 volt Li-Ion batteries for 8mm, VHS-C, digital
camcorders and digital cameras from Nikon, Kodak, Fuji, Sharp,
Sony, Canon, JVC, Panasonic, RCA and other manufacturers. In
addition to the other adapter plates for other Li-Ion battery models.
camcorder battery charger which is compatible with virtually all 3.6
volt and 7.4 volt Li-Ion batteries for 8mm, VHS-C, digital
camcorders and digital cameras from Nikon, Kodak, Fuji, Sharp,
Sony, Canon, JVC, Panasonic, RCA and other manufacturers. In
addition to the other adapter plates for other Li-Ion battery models.
This charger uses an advanced charging circuit, which provides a
safe, full charge every time. “Charging” and “Full Charge” status of
the battery is shown on the built-in LED indicators.
safe, full charge every time. “Charging” and “Full Charge” status of
the battery is shown on the built-in LED indicators.
Flexible power input allows you to use the OmniSource Li-Ion from
home with its AC Power Supply or on the road using the DC
Cigarette Lighter Adapter included. Avoid prolonged use in an
automobile when the engine is not running as it may drain the battery
in the vehicle.
home with its AC Power Supply or on the road using the DC
Cigarette Lighter Adapter included. Avoid prolonged use in an
automobile when the engine is not running as it may drain the battery
in the vehicle.
Getting Ready
Choose the adapter plate for the type of battery you will be charging.
Each of the adapter plates is labeled as to the batteries it can work
with. If the charger base does not already have the adapter plate you
want attached, you will need to remove the adapter plate first by
pushing down on the plate and sliding it to the rear of the charger
base (away from the LED indicators). Then, attach the selected
adapter plate to the charger unit by aligning the arrows on the sides
of the adapter plates and the charger base as shown. While pressing
down lightly on the adapter plate, slide the plate toward the front of
the charger base until it locks.
Each of the adapter plates is labeled as to the batteries it can work
with. If the charger base does not already have the adapter plate you
want attached, you will need to remove the adapter plate first by
pushing down on the plate and sliding it to the rear of the charger
base (away from the LED indicators). Then, attach the selected
adapter plate to the charger unit by aligning the arrows on the sides
of the adapter plates and the charger base as shown. While pressing
down lightly on the adapter plate, slide the plate toward the front of
the charger base until it locks.
Plug-in, either the AC Adapter or the DC Cigarette Lighter power
adapter, and connect the other end of the power adapter cable to the
power input jack on the rear of the charger unit.
Status LED’s
Together, the three LED’s on the front of the OmniSource Li-Ion
will indicate the status of the battery and the charger. See the
descriptions and diagrams included in the following sections
regarding the various indications and their meaning.
adapter, and connect the other end of the power adapter cable to the
power input jack on the rear of the charger unit.
Status LED’s
Together, the three LED’s on the front of the OmniSource Li-Ion
will indicate the status of the battery and the charger. See the
descriptions and diagrams included in the following sections
regarding the various indications and their meaning.
Operation:
Plug-in, either the AC 110V or the DC Cigarette Lighter power
adapter, depending on where you are going to use your OmniSource
Li-Ion charger unit. Connect the other end of the power adapter cable
to the power input socket on the charger unit. While the unit is
receiving power, the red Power Indicator LED on the far right, will
be on. (See diag.-1).
Plug-in, either the AC 110V or the DC Cigarette Lighter power
adapter, depending on where you are going to use your OmniSource
Li-Ion charger unit. Connect the other end of the power adapter cable
to the power input socket on the charger unit. While the unit is
receiving power, the red Power Indicator LED on the far right, will
be on. (See diag.-1).
Diag.-1
Connect the battery to the adapter plate on the charger unit, and the
red Charge Indicator LED in the center will turn on to indicate that
the unit is fast charging your battery.
red Charge Indicator LED in the center will turn on to indicate that
the unit is fast charging your battery.
Diag.-2
When the red Charge LED turns off, and the green Charge Complete
LED, turns on, the charger has switched to “trickle” charge mode
and the battery is around 90% charged at this time. The battery will
reach 100% charge within 1-2 hours (depending on the capacity of
the battery) after the green LED has turned on. Be sure to remove the
battery from the charger within a few hours after the green LED has
turned on.
LED, turns on, the charger has switched to “trickle” charge mode
and the battery is around 90% charged at this time. The battery will
reach 100% charge within 1-2 hours (depending on the capacity of
the battery) after the green LED has turned on. Be sure to remove the
battery from the charger within a few hours after the green LED has
turned on.
Diag.-3