HP RC3000 Manual Do Utilizador
RC3000 Antenna Controller
Chapter 3
Detailed Operation
128
3.3.2.11 Configuration Item Record
Selecting the Stop/. key from the MAINTENANCE screens triggers a process that will transmit the current
configuration item values via the remote control port.
configuration item values via the remote control port.
If the controller has the remote control option, the values will be transmitted at the baud rate set in the
Remote configuration screen. Otherwise the default rate of 9600 baud will be used. The data will be sent
out as 7 data bits with even parity. The data is sent out as a simple set of ASCII characters with each line
terminated by a linefeed and carriage return. It is intended that a simple program such as HyperTerminal
be used to pull in the data.
Remote configuration screen. Otherwise the default rate of 9600 baud will be used. The data will be sent
out as 7 data bits with even parity. The data is sent out as a simple set of ASCII characters with each line
terminated by a linefeed and carriage return. It is intended that a simple program such as HyperTerminal
be used to pull in the data.
The output's first three lines will contain date, time, mount type, software version number, etc. Next the
configuration items will be sent out per configuration screen. For each configuration item, the field shown
on the screen, the item value and the bottom row prompt associated with the item will be sent on one line.
The following is an example output showing the first two configuration screens.
configuration items will be sent out per configuration screen. For each configuration item, the field shown
on the screen, the item value and the bottom row prompt associated with the item will be sent on one line.
The following is an example output showing the first two configuration screens.
RC3000 CONFIGURATION ITEMS
20OCT05 20:49:21
V1-GTR 1.54
SYSTEM DEFINITION
SN: 1234 SERIAL NUMBER<1-9999> (0=NOT ENTERED)
GPS: 1 <1>GPS PRESENT <0>NOT PRESENT
COMPASS: 1 <0>NONE <1>TRUCK MOUNT <2>ANTENNA MOUNT
MODE: 2 <1-LOCATE 2-MENU 3-MANUAL 4-VSAT 5-POS>
ANT_SIZE: 244 ANTENNA SIZE <1-9999 CM>
WAVEGUIDE: 0 WAVEGUIDE SWITCH <1>PRESENT <0>NONE
ELEVATION CALIBRATION
REF_V: 1.69 SET ZERO VOLTAGE <0.50 - 4.50>
OFF: 0.0 ELEVATION OFFSET <-25.0/+25.0 DEGREES>
UP: 90 SET UP LIMIT <0-90 DEGREES>
DOWN: 0 SET DOWN LIMIT <0-90 DEGREES>
SF: 50.00 SCALE FACTOR <30.00 - 60.00 mV/deg>
LOOK: 1 ELEV LOOK CONFIGURATION <1>HIGH <0>LOW
20OCT05 20:49:21
V1-GTR 1.54
SYSTEM DEFINITION
SN: 1234 SERIAL NUMBER<1-9999> (0=NOT ENTERED)
GPS: 1 <1>GPS PRESENT <0>NOT PRESENT
COMPASS: 1 <0>NONE <1>TRUCK MOUNT <2>ANTENNA MOUNT
MODE: 2 <1-LOCATE 2-MENU 3-MANUAL 4-VSAT 5-POS>
ANT_SIZE: 244 ANTENNA SIZE <1-9999 CM>
WAVEGUIDE: 0 WAVEGUIDE SWITCH <1>PRESENT <0>NONE
ELEVATION CALIBRATION
REF_V: 1.69 SET ZERO VOLTAGE <0.50 - 4.50>
OFF: 0.0 ELEVATION OFFSET <-25.0/+25.0 DEGREES>
UP: 90 SET UP LIMIT <0-90 DEGREES>
DOWN: 0 SET DOWN LIMIT <0-90 DEGREES>
SF: 50.00 SCALE FACTOR <30.00 - 60.00 mV/deg>
LOOK: 1 ELEV LOOK CONFIGURATION <1>HIGH <0>LOW
NOTE: During the time (up to 15 seconds) its takes to output all configuration item values, there will be no
action apparent at the RC3000's front panel. The user should monitor his recording program to
determine when the process is finished. Note also that this process will disrupt normal remote control
actions so any other monitor and control applications should be paused during this process.
action apparent at the RC3000's front panel. The user should monitor his recording program to
determine when the process is finished. Note also that this process will disrupt normal remote control
actions so any other monitor and control applications should be paused during this process.
The intent of this feature is to provide a convenient way to record configuration item values following the
calibration of the controller. Before contacting RCI for technical support, it would also be useful to record
the current configuration items status and send the file to RCI.
calibration of the controller. Before contacting RCI for technical support, it would also be useful to record
the current configuration items status and send the file to RCI.