Honeywell ADEMCO 6150RF Guia Da Instalação
- 2 -
WIRING TABLE
Keypad
Control Panel
Wire Color
▲
G
Data In
Green
−
− Aux Pwr (GND)
Black
+
+ Aux Pwr
Red
▼
Y
Data Out
Yellow
Note: NO (normally Open) and C (common) are the
connections for the relay output
+
6150RF-003-V2
NO C
Y
G
Figure 2 - 6150RF Wiring Connections
APPLICATION GUIDELINES
Use the following guidelines when planning an installation:
• Local wireless keys (wireless keys programmed directly into the 6150RF) may be used regardless of whether the
Use the following guidelines when planning an installation:
• Local wireless keys (wireless keys programmed directly into the 6150RF) may be used regardless of whether the
RF receiver in the 6150RF is enabled or disabled.
• If using bi-directional devices, be sure to enable the transmitter module in the 6150RF.
• If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not
• If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not
exceed the number of receivers supported by the control panel.)
• If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be
entered into the 6150RF. This user code must also be programmed into the control panel.
• You must set the House ID only if you are using RF keypads and/or bi-directional devices; AND the House ID
Source is the 6150RF (Local).
6150RF Application Guide
The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the 6150RF for your
installation.
The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the 6150RF for your
installation.
* Two 6150RFs are needed for this application: one assigned to partition 1 and one assigned to partition 2.
** If using an RF keypad on only one partition, the 6150RF’s partition assignment in panel programming must match the partition.
*** If set for Local on a partition control, the 6150RF’s partition assignment must match the one programmed in the BD device.
Are you using
6150RF Programming Options
System Control Panel
RF keys
beyond
system’s
capacity?
RF receivers
beyond
system’s
capacity?
RF keypads and/or
Bi-directional
devices on more
than 1 partition?
than 1 partition?
Program
Wireless Keys
Into
Receiver
Enable
House ID
Source***
4110DL, 4110XM, 4140XMP,
VISTA-20HWSE
VISTA-20HWSE
N/A
N/A
N/A
6150RF
OFF
Local [0]
NO
NO
N/A
System
ON [1]
System [1]
YES
NO
N/A
6150RF
ON [1]
System [1]
VISTA-10P, VISTA-10SE, VISTA-
15, VISTA-15P, VIA-30PSE
15, VISTA-15P, VIA-30PSE
YES
YES
N/A
6150RF
OFF [0]
Local [0]
NO
NO
NO
System
ON [1]
System [1]
YES
NO
NO
6150RF
ON [1]
System [1]
YES
YES
NO
6150RF
OFF [0]
Local [0]
NO
YES
YES*
System
OFF [0]
Local [0]
VISTA-20SE, VISTA-20P
YES
YES
YES*
6150RF
OFF [0]
Local [0]
NO
NO
NO**
System
ON [1]
System [1]
YES
NO
NO**
6150RF
ON [1]
System [1]
YES
YES
NO**
6150RF
OFF [0]
Local [0]
NO
YES
YES
System
OFF [0]
Local [0]
VISTA-40, VISTA-50P, VISTA-
128B, VISTA-128BP
128B, VISTA-128BP
YES
YES
YES
6150RF
OFF [0]
Local [0]