Hollywood Express Bicycle Carrier E3 Manual Do Utilizador
When using your new Hollywood E3 Express rack, please follow
these important recommendations:
these important recommendations:
Install the Express rack on structurally sound trunks and rear decks
only. If you own a Mini Van or Sport Utility Vehicle (SUV), be sure to
read the special notes below.
Never attach hooks to aluminum, plastic, glass, fiberglass or carbon
fiber. If in doubt, check the surface with a magnet. If the magnet
sticks, it’s okay to use the rack. If not, do not use the rack on the
only. If you own a Mini Van or Sport Utility Vehicle (SUV), be sure to
read the special notes below.
Never attach hooks to aluminum, plastic, glass, fiberglass or carbon
fiber. If in doubt, check the surface with a magnet. If the magnet
sticks, it’s okay to use the rack. If not, do not use the rack on the
subject vehicle. The rack strap hooks can damage non-steel surfaces. Hooks may be attached to roof rack
cross bars. Check the contour of the bar first to be certain that it will accept and retain the hook securely.
Clean the surface of the trunk, rear door or deck lid before installation of the rack. Clean the surfaces of
the sponge pads on your Express rack. Dirt trapped between the pads of the rack and the trunk can scratch
the vehicle’s paint due to the abrasive composition of dirt.
Tighten all six straps both before and after mounting bikes on the rack.
Never place more than 100 lbs. (45 KG) on either the Express rack.
Use the upper rubber tie down straps, two per bike when securing your bike(s) to the rack.
Always use the attached Safety Strap after loading all of the bicycles onto the Express rack. This final
Safely Strap should be threaded through all of the bikes, and the frame of the Express rack itself.
Keep the bicycle tires at least one foot away from the
exhaust pipe(s). Automotive exhaust is hot enough to melt
bicycle tires.
Check the rack, bikes and straps regularly during use.
Drive slowly when used on bumpy or rock/dirt surface
roads.
cross bars. Check the contour of the bar first to be certain that it will accept and retain the hook securely.
Clean the surface of the trunk, rear door or deck lid before installation of the rack. Clean the surfaces of
the sponge pads on your Express rack. Dirt trapped between the pads of the rack and the trunk can scratch
the vehicle’s paint due to the abrasive composition of dirt.
Tighten all six straps both before and after mounting bikes on the rack.
Never place more than 100 lbs. (45 KG) on either the Express rack.
Use the upper rubber tie down straps, two per bike when securing your bike(s) to the rack.
Always use the attached Safety Strap after loading all of the bicycles onto the Express rack. This final
Safely Strap should be threaded through all of the bikes, and the frame of the Express rack itself.
Keep the bicycle tires at least one foot away from the
exhaust pipe(s). Automotive exhaust is hot enough to melt
bicycle tires.
Check the rack, bikes and straps regularly during use.
Drive slowly when used on bumpy or rock/dirt surface
roads.
Mounting the Hollywood Express Rack on Your Vehicle:
Your new Express 3-bike rack comes to you fully assembled
in the box, so there is no assembly to do on the rack itself.
There will be some adjustment and set-up required so that the
Express will fit on your vehicle correctly. Please read and
adhere to all instructions as follows:
in the box, so there is no assembly to do on the rack itself.
There will be some adjustment and set-up required so that the
Express will fit on your vehicle correctly. Please read and
adhere to all instructions as follows:
1. After removing your Express rack from the box, loosen the black hubs by turning the hub adjustment
knobs counter-clockwise. This will allow the two sections of the rack frame to move relative to one another
for correct rack placement on your vehicle. Note how the teeth on the hubs interlock into place. See Fig. 2.
The Express is adjustable to clear small spoilers.
knobs counter-clockwise. This will allow the two sections of the rack frame to move relative to one another
for correct rack placement on your vehicle. Note how the teeth on the hubs interlock into place. See Fig. 2.
The Express is adjustable to clear small spoilers.
2. Adjusting the rack frame: Position the Express rack on the vehicle such that the bicycle support arms
are parallel to the ground, or angled slightly upward at the back of the rack. The rear brace should rest on a
steel trunk lid, or rear door. See Fig. 1. If necessary (especially on vans, station wagons and SUV’s) the
upper pads may rest on glass. This is because the weight of the rack and bicycles is support by the upper
straps, and the lower pads. Be careful not to interfere with the rear mounted wiper blade if the vehicle is so
equipped.
3. Once the proper rack position has been determined by adjusting the Express rack’s bicycle support arms
and rear brace, tighten the hubs by turning both black knobs in a clockwise (right hand thread) direction,
are parallel to the ground, or angled slightly upward at the back of the rack. The rear brace should rest on a
steel trunk lid, or rear door. See Fig. 1. If necessary (especially on vans, station wagons and SUV’s) the
upper pads may rest on glass. This is because the weight of the rack and bicycles is support by the upper
straps, and the lower pads. Be careful not to interfere with the rear mounted wiper blade if the vehicle is so
equipped.
3. Once the proper rack position has been determined by adjusting the Express rack’s bicycle support arms
and rear brace, tighten the hubs by turning both black knobs in a clockwise (right hand thread) direction,
Fig. 2
Installation Instructions for Hollywood
Model E3 Express bicycle carrier
Model E3 Express bicycle carrier
1