Aviom AV-P2 Manual Do Utilizador
Channels 1-16
Channels 17-32
EXPANSION
OUT
EXPANSION
OUT
To configure a 16 x 16 system:
Set up one input module (AV-M8, pair of AV-M8s, Y1
card, AN-16/i or AN-16/i-M) and one output module on
each side of the network.
Connect 16 mic- or line-level audio sources to inputs
1-16 on the first Pro16 Series input module.
Connect a Cat-5e cable from the A-N
card, AN-16/i or AN-16/i-M) and one output module on
each side of the network.
Connect 16 mic- or line-level audio sources to inputs
1-16 on the first Pro16 Series input module.
Connect a Cat-5e cable from the A-N
et
o
ut
port on the
first input module to the A-N
et
e
xpANsioN
port on the
first output module.
Plug a Cat-5e cable into the A-N
Plug a Cat-5e cable into the A-N
et
i
N
port on the first
output module. This cable will be used to span up
to 500 feet/150 meters between the two sides of the
network.
Connect the cable from the A-N
to 500 feet/150 meters between the two sides of the
network.
Connect the cable from the A-N
et
i
N
port in Step 4 to
the A-N
et
o
ut
port on the second Pro16 Series input
module.
Connect the second group of 16 audio sources to
inputs 1-16 on the second Pro16 Series input module.
Connect a Cat-5e cable from the A-N
Connect the second group of 16 audio sources to
inputs 1-16 on the second Pro16 Series input module.
Connect a Cat-5e cable from the A-N
et
e
xpANsioN
port
on the second input module to A-N
et
i
N
on the second
Pro16 output module.
Patch the audio outputs from the two output modules
into the desired destinations.
Patch the audio outputs from the two output modules
into the desired destinations.
Adding More Audio Outputs
As mentioned previously, the A-Net Out ports on AN-16/o and AV-P2
output modules and Personal Mixer products remain available even
output modules and Personal Mixer products remain available even
1.
2.
3.
4.
5.
6.
7.
8.
POWER
ON
EXPANSION
OUT
IN
AV-M8
STEREO LINK
CLOCK SOURCE
INTERNAL
ADAT
CH 9-16
250VAC-F4AL
OUT
ADAT
®
POWER
ON
EXPANSION
OUT
IN
AV-M8
STEREO LINK
CLOCK SOURCE
INTERNAL
ADAT
CH 9-16
250VAC-F4AL
OUT
ADAT
®
Channels 1-16 in
Channels 17-32 in
Channels 1-16 out
Channels 17-32 out
Note that A-Net In is connected to A-Net Out on both pairs of modules
in this 32 x 0 system.
The AV-P2 can be substituted for the output module that supplies
channels 17-32 if desired. It cannot be substituted for the output module
supplying channels 1-16 because the AV-P2 does not have the A-Net
Expansion port.
channels 17-32 if desired. It cannot be substituted for the output module
supplying channels 1-16 because the AV-P2 does not have the A-Net
Expansion port.
16 Channels Send by 16 Channels Return
The 16 x 16 configuration has 16 inputs and 16 outputs on each side of
the audio network.
the audio network.
A-Net
A-Net Expansion
Pro16 Output
Pro16 Input
Pro16 Output
Pro16 Input
Channels 1-16 In
Channels 1-16 Out
Channels 17-32 In
Channels 17-32 Out
Using this configuration, each side of the audio network has one input
module and one Pro16 output module. Sixteen channels of audio move
in each direction over a single Cat-5e cable.
module and one Pro16 output module. Sixteen channels of audio move
in each direction over a single Cat-5e cable.
The AV-P2 can be used to output channels 17-32 in this diagram. It
cannot be substituted for the output module supplying channels 1-16
because the AV-P2 does not have the A-Net Expansion port.
cannot be substituted for the output module supplying channels 1-16
because the AV-P2 does not have the A-Net Expansion port.
Again, the A-Net Expansion port is used to combine the A-Net data from
two devices for transmission over one Cat-5e cable.
two devices for transmission over one Cat-5e cable.