Alpine DVA-9861 Manual Do Utilizador
21
-EN
Adjusting Bass/Treble/Balance (Between
Left and Right)/Fader (Between Front
and Rear)/Defeat
Left and Right)/Fader (Between Front
and Rear)/Defeat
1
Press MODE repeatedly to choose the desired
mode.
mode.
Each press changes the modes as follows:
BASS
TREBLE
SUBW*
BALANCE
FADER
DEFEAT
VOLUME
BASS
Bass level: –7 ~ +10
Treble level: –7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Treble level: –7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
• If MODE is not pressed within 5 seconds after selecting the BASS,
TREBLE, BALANCE, FADER, DEFEAT or SUBW mode, the unit
automatically returns to normal mode.
automatically returns to normal mode.
* When the subwoofer mode is set to OFF, its level cannot be adjusted.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting Defeat ON, previously adjusted settings of BASS
and TREBLE will return to the factory defaults.
obtained in each mode.
By setting Defeat ON, previously adjusted settings of BASS
and TREBLE will return to the factory defaults.
• Depending on the connected devices, some functions and display
indications do not work.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
preference.
1
Press MENU to select the BASS ENGINE mode, then
press MODE.
press MODE.
BBE
BASS ENGINE
SETUP
RETURN (OFF)
BBE
2
Press
or
to select the BASS (bass Center
frequency) control mode.
BASS
TREBLE
3
-1 Press SOURCE/POWER to select the desired bass
center frequency.
80Hz
100Hz
120Hz
60Hz
80Hz
Emphasizes the displayed bass frequency ranges.
3
-2 Press BAND to select the desired bass bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wide setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
wide setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
3
-3
*1
Turn the Rotary encoder to select the desired
bass level (–7~+10).
You can emphasize or weaken the bass level.
bass level (–7~+10).
You can emphasize or weaken the bass level.
4
Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
After 2 seconds, the unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• If no operation is performed within 60 seconds, the bass control
setting will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, AM, CD, etc.) until the setting is changed. The bass
frequency and bass band width settings adjusted for one source are
effective for all other sources (FM, AM, CD etc.).
frequency and bass band width settings adjusted for one source are
effective for all other sources (FM, AM, CD etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
audio processor with the Bass function is connected.
• This function is inoperable when DEFEAT is set to ON.
• While in the bass adjusting mode, TREBLE CONTROL adjusting
• While in the bass adjusting mode, TREBLE CONTROL adjusting
mode can be recalled by pressing
or
.
*
1
The adjustment can also be made by pressing MODE. Refer to
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 21)
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 21)
Sound Setting
Rotary encoder
BAND
MODE
SOURCE/
POWER
POWER
MENU
Setting the Bass Center Frequency
Setting the Bass Bandwidth
Setting the Bass Level