Delta Tau GEO BRICK LV Manual Do Utilizador
Turbo PMAC User Manual
Setting Up Turbo PMAC-Based Commutation and/or Current Loop
105
•
For synchronous motors (and probably for induction motors), the physical change in rotor position
between the initial Step 1 and the return to Step 1 (mark the rotor if necessary) should be equal to 1
pole pair:
between the initial Step 1 and the return to Step 1 (mark the rotor if necessary) should be equal to 1
pole pair:
•
On a 2-pole motor, it should be one full mechanical revolution.
•
On a 4-pole motor, it should be one-half mechanical revolution.
•
On a 6-pole motor, it should be one-third mechanical revolution.
•
On an 8-pole motor, it should be one-fourth mechanical revolution.
•
On a 100-pole motor, it should be 7.2
o
mech.
Executing the Test
For Motor 1 using Servo IC 0, Channel 1 with a 3-phase motor, with 10% voltage commands being
acceptable, the commands could be:
For Motor 1 using Servo IC 0, Channel 1 with a 3-phase motor, with 10% voltage commands being
acceptable, the commands could be:
M102=0 M104=I7000/10 M107=-I7000/10
; Step 1: A0, B+, C-: 0oelec.
M102=I7000/10 M104=0 M107=-I7000/10
; Step 2: A+, B0, C-: 60oelec.
M102=I7000/10 M104=-I7000/10 M107=0
; Step 3: A+, B-, C0: 120oelec.
M102=0 M104=-I7000/10 M107=I7000/10
; Step 4: A0, B-, C+: +180oelec.
M102=-I7000/10 M104=0 M107=I7000/10
; Step 5: A-, B0, C+: -120oelec.
M102=-I7000/10 M104=I7000/10 M107=0
; Step 6: A-, B+, C0: -60oelec.
M102=0 M104=I7000/10 M107=-I7000/10
; Step 1: A0, B+, C-: 0oelec.
This test moves the motor through the commutation cycle in the positive direction if Ixx72 is less than
1024 (i.e. 683); it moves through the cycle in the negative direction if Ixx72 is greater than 1024 (i.e.
1365). On a synchronous motor, we can use the position reading to check the commutation polarity
match; this may be possible on an induction motor as well.
1024 (i.e. 683); it moves through the cycle in the negative direction if Ixx72 is greater than 1024 (i.e.
1365). On a synchronous motor, we can use the position reading to check the commutation polarity
match; this may be possible on an induction motor as well.
Action To Take
If the rotor position, as reflected by M101, changed in the wrong direction during this test, we could have
a commutation polarity mismatch. With such a mismatch, the motor would lock in (not run away) when
commanded. There are two possible fixes for this mismatch:
1. Reverse the feedback direction sense by changing I7mn0. However, this changes the direction sense
If the rotor position, as reflected by M101, changed in the wrong direction during this test, we could have
a commutation polarity mismatch. With such a mismatch, the motor would lock in (not run away) when
commanded. There are two possible fixes for this mismatch:
1. Reverse the feedback direction sense by changing I7mn0. However, this changes the direction sense
of the axis, which may not be tolerable.
2. Exchange two phase leads between amplifier and motor. Usually, this is done at the screw terminals
on the amplifier. Exchanging any two phases will change the polarity in the same way. However, the
relationship between the sensor zero position and Turbo PMAC’s commutation cycle zero position is
dependent on which two phases are exchanged.
relationship between the sensor zero position and Turbo PMAC’s commutation cycle zero position is
dependent on which two phases are exchanged.
For asynchronous induction motors, if the above test did not cause proper movement try each direction
polarity and see which works. This is described below.
polarity and see which works. This is described below.
Once the commutation polarity match has been established, the servo polarity match is established
automatically. Check this later by seeing that positive O-commands cause motor position to count in the
positive direction.
automatically. Check this later by seeing that positive O-commands cause motor position to count in the
positive direction.
Remember that if I7mn0 is changed later to get the physical direction sense needed, exchange motor
phase leads to re-establish the commutation polarity match.
phase leads to re-establish the commutation polarity match.