BMW 2006 X5 3.0i SAV Manual Do Proprietário
115
n
Ov
er
v
iew
Con
tr
o
ls
M
a
in
te
na
nc
e
Re
p
a
ir
s
Da
ta
In
de
x
Integrated universal remote control
*
Programming
1 Memory buttons
2 LED
Fixed-code hand-held transmitter
1. Switch on the ignition.
2. For initial use: press both outer
2. For initial use: press both outer
buttons 1 for approx. 20 seconds
until the LED 2 flashes. The three
memory buttons 1 are cleared.
until the LED 2 flashes. The three
memory buttons 1 are cleared.
3. Hold the original hand-held transmit-
ter at a distance of approx. 2 to 8 in/
5 to 20 cm from the memory but-
tons 1.
5 to 20 cm from the memory but-
tons 1.
The required distance between
the hand-held transmitter and
the hand-held transmitter and
memory buttons 1 depends on the
relevant system of the original hand-
held transmitter used.
relevant system of the original hand-
held transmitter used.
<
53
0u
e
2
64
4. Simultaneously press the transmit
button on the original hand-held
transmitter and the desired memory
button 1 of the integrated universal
remote control. The LED 2 flashes
slowly at first. As soon as the LED 2
flashes rapidly, release both buttons.
If the LED 2 does not flash rapidly
after approx. 15 seconds, alter the
distance.
transmitter and the desired memory
button 1 of the integrated universal
remote control. The LED 2 flashes
slowly at first. As soon as the LED 2
flashes rapidly, release both buttons.
If the LED 2 does not flash rapidly
after approx. 15 seconds, alter the
distance.
5. To program other original hand-held
transmitters, repeat steps 3 and 4.
The corresponding memory button 1 is
now programmed with the signal of the
original hand-held transmitter.
now programmed with the signal of the
original hand-held transmitter.
You can operate the system when the
engine is running or when the ignition is
switched on.
engine is running or when the ignition is
switched on.
If the system cannot be operated
after repeated programming,
after repeated programming,
check whether the original hand-held
transmitter uses an alternating-code
system. To do so, either read the
instructions of the original hand-held
transmitter or press and hold down the
programmed memory button 1 of the
integrated universal remote control.
transmitter uses an alternating-code
system. To do so, either read the
instructions of the original hand-held
transmitter or press and hold down the
programmed memory button 1 of the
integrated universal remote control.
If the LED 2 on the integrated universal
remote control flashes quickly for a
brief period and then remains lit up for
approx. two seconds, this indicates that
the original hand-held transmitter is
equipped with an alternating code. In
the case of an alternating-code system,
program the memory buttons 1 as
described in the section on alternating-
code hand-held transmitters.
If you have additional questions, please
consult your BMW Sports Activity Vehi-
cle center or call 1-800-355-3515.
You can also visit our website
www.bmwusa.com.
remote control flashes quickly for a
brief period and then remains lit up for
approx. two seconds, this indicates that
the original hand-held transmitter is
equipped with an alternating code. In
the case of an alternating-code system,
program the memory buttons 1 as
described in the section on alternating-
code hand-held transmitters.
If you have additional questions, please
consult your BMW Sports Activity Vehi-
cle center or call 1-800-355-3515.
You can also visit our website
www.bmwusa.com.
<
Alternating-code hand-held
transmitter
transmitter
To program the integrated universal
remote control, consult the Owner's
Manuals for the equipment to be set.
You will find information there on the
possibilities for synchronization.
When programming alternating-code
hand-held transmitters, please follow
the supplementary instructions below:
remote control, consult the Owner's
Manuals for the equipment to be set.
You will find information there on the
possibilities for synchronization.
When programming alternating-code
hand-held transmitters, please follow
the supplementary instructions below:
Programming will be easier with
the aid of a second person.
the aid of a second person.
<
Online Edition for Part No. 01 41 0 159 867 - © 07/05 BMW AG