Alpine CDA-9812RB Manual Do Utilizador
33
-EN
MobileHub™ Link
Operation(Optional)
Operation(Optional)
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone while
driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone while
driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
• If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
• Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
1
Press and hold BAND/TEL. for at least 2 seconds
to turn on the Telephone mode.
to turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
See relevant pages for each item.
• When a portable telephone is not connected, press and hold
BAND/TEL. for at least 2 seconds. “NO PHONE” is displayed for
about 2 seconds, then the mode returns to the original source
mode.
about 2 seconds, then the mode returns to the original source
mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of CDA-9815RB/
CDA-9813R/CDA-9812RX/CDA-9811R is off, the power of CDA-
9815RB/CDA-9813R/CDA-9812RX/CDA-9811R will turn on
automatically for a hands-free call.
9815RB/CDA-9813R/CDA-9812RX/CDA-9811R will turn on
automatically for a hands-free call.
• Even if the power of the portable telephone is off, when CDA-
9815RB/CDA-9813R/CDA-9812RX/CDA-9811R is set to Telephone
mode, the power of the portable telephone will be turned on.
mode, the power of the portable telephone will be turned on.
• Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
disconnected, and an ordinary call by the portable telephone is
possible.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
incoming or talking mode.
SOURCE/
POWER
POWER
Preset buttons
(1 through 6)
(1 through 6)
BAND/
TEL.
TEL.
f
g
Rotary encoder
SEARCH
F/SETUP
-/J
9
8
TITLE
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9815RB/CDA-9813R/CDA-
9812RX/CDA-9811R as malfunction can result.
from a portable telephone and CDA-9815RB/CDA-9813R/CDA-
9812RX/CDA-9811R as malfunction can result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
• The telephone volume can be adjusted on the CDA-9815RB/CDA-
9813R/CDA-9812RX/CDA-9811R. The volume you set during the
call is memorized, and is automatically applied again on the next
call.
call is memorized, and is automatically applied again on the next
call.
• While telephoning or receiving incoming calls, press TITLE to
show the Network Operator display for 5 seconds.
Incoming Calls
1
Press :/J to receive an incoming call.
2
Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source
mode.
mode.
• When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call.
• The incoming call can be switched to Automatic Calling or Manual
Calling.
1 Press and hold F/SETUP for at least 3 seconds.
2 Select the Telephone mode by pressing g or f.
3 Press BAND/TEL. to change to AUTO or MANUAL
(MANU).
4 Press F/SETUP to return to normal mode.
• Press BAND/TEL. during an incoming call to disconnect it.