White Outdoor Snow Boss 750T Manual Do Utilizador
11
Chute Directional Control And Support
Bracket Adjustment
Bracket Adjustment
If the spiral at the base of the chute directional control is
not fully engaging with the notches in the lower chute
assembly, the support bracket can be adjusted inward
or outward as follows:
not fully engaging with the notches in the lower chute
assembly, the support bracket can be adjusted inward
or outward as follows:
•
Loosen, but do NOT remove the two hex nuts
which secure the chute directional control support
bracket to the snow thrower housing.
See Figure 10.
which secure the chute directional control support
bracket to the snow thrower housing.
See Figure 10.
Figure 10
•
Adjust the support bracket inward or outward so
that the spiral is fully engaged in the notches on the
chute before retightening the hex nuts.
that the spiral is fully engaged in the notches on the
chute before retightening the hex nuts.
Shift Rod Adjustment
To adjust the shift rod, proceed as follows:
•
Remove the hairpin clip and slide the shift rod
connector up, to separate the upper shift rod from
the lower shift rod. See Figure 11.
connector up, to separate the upper shift rod from
the lower shift rod. See Figure 11.
•
Place the shift lever into the sixth (6) position.
•
Rotate the shift arm clockwise (from the operator’s
position) as far as it will go.
position) as far as it will go.
•
Thread the upper shift rod downward until the
elbow on its lower end aligns with the hole found in
the lower shift rod.
elbow on its lower end aligns with the hole found in
the lower shift rod.
•
Reconnect the upper shift rod to the lower shift rod
by reinserting the hairpin clip removed earlier and
sliding the shift rod connector back down into place.
by reinserting the hairpin clip removed earlier and
sliding the shift rod connector back down into place.
IMPORTANT:
Make certain to check for correct
adjustment of the shift rod as instructed under Final
Adjustments in the Assembly Section, before operating
the snow thrower.
Adjustments in the Assembly Section, before operating
the snow thrower.
Figure 11
Chute Assembly Adjustment
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Refer to the
Chute Tilt Control in the Know Your Snow Thrower
Section.
adjusting the angle of the chute assembly. Refer to the
Chute Tilt Control in the Know Your Snow Thrower
Section.
Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes. Refer
to Skid Shoe Adjustment in the Assembly Section.
be adjusted by raising or lowering the skid shoes. Refer
to Skid Shoe Adjustment in the Assembly Section.
SECTION 6: MAINTAINING YOUR SNOW THROWER
WARNING: Before lubricating, repairing,
or inspecting, disengage all clutch levers
and stop engine. Wait until all moving
parts have come to a complete stop.
Disconnect spark plug wire and ground it
against the engine to prevent unintended
starting.
or inspecting, disengage all clutch levers
and stop engine. Wait until all moving
parts have come to a complete stop.
Disconnect spark plug wire and ground it
against the engine to prevent unintended
starting.
Lubrication
Gear Shaft
Lubricate the gear shaft with 6-n-1 grease at least once
a season or after every 25 hours of operation (available
at automotive stores, or order part number 737-0170).
a season or after every 25 hours of operation (available
at automotive stores, or order part number 737-0170).
Refer to Figure 9.
IMPORTANT:
Keep all grease and oil off of the rubber
friction wheel and aluminum drive plate.
Spiral
Support
Bracket
Bracket
Hex Nuts
Shift Lever
Upper Shift Rod
Lower Shift Rod
Connector
Ferrule
Hairpin
Clip
Clip
Shift Arm