White Outdoor RB650 Manual Do Utilizador
10
Figure 8
•
To transport tiller, lower the depth stake (use top
adjustment hole).
adjustment hole).
•
To adjust the depth stake, remove the clevis pin
and hairpin clip. See Figure 8. Move the depth
stake to the desired setting.
and hairpin clip. See Figure 8. Move the depth
stake to the desired setting.
•
To adjust the side shields, remove the front wing
nut and loosen the rear wing nut. See Figure 9.
Place side shield in position desired. Replace wing
nuts and tighten securely.
nut and loosen the rear wing nut. See Figure 9.
Place side shield in position desired. Replace wing
nuts and tighten securely.
Figure 9
TO OPERATE THE TILLER:
•
Select the depth stake setting.
•
Start engine as instructed on page 9.
•
Move gear selection handle to one of the forward
modes or reverse.
modes or reverse.
Use the reverse tine drive when tilling virgin
ground, sod or hard soil. Use the forward tine
drive when cultivating or tilling soft ground.
ground, sod or hard soil. Use the forward tine
drive when cultivating or tilling soft ground.
IMPORTANT:
When using the forward tine drive, lower
the depth stake (use a shallower tilling depth) to make
certain the tines do not run across the ground.
certain the tines do not run across the ground.
WARNING:
Do not move the gear
selection handle with the wheels or tines
engaged. Make certain the unit is stopped
completely before changing the gear
selection.
engaged. Make certain the unit is stopped
completely before changing the gear
selection.
•
Squeeze the clutch control bail against the handle
to engage the wheels and tines.
to engage the wheels and tines.
NOTE: Make certain the gear selection indicator is
correctly positioned before engaging the clutch handle.
If it is between gears, the engine will stall.
correctly positioned before engaging the clutch handle.
If it is between gears, the engine will stall.
To transport tiller, do not engage the tines. Select the
wheel drive only.
wheel drive only.
WARNING:
Do not push down on the
handles so that the wheels are lifted off
the ground while using the reverse tine
drive, or the tiller could move backward
and cause personal injury.
the ground while using the reverse tine
drive, or the tiller could move backward
and cause personal injury.
For best results, it is recommended the garden be tilled
twice (lengthwise, then widthwise) to pulverize the soil.
twice (lengthwise, then widthwise) to pulverize the soil.
SECTION 6: MAKING ADJUSTMENTS
HANDLE ADJUSTMENT
The handle height may be adjusted. Refer to the Know
Your Tiller section for details of handle adjustment.
Your Tiller section for details of handle adjustment.
BELT TENSION ADJUSTMENT
Periodic adjustment of the belt tension may be required
due to normal stretch and wear on the belt. Adjustment
is needed if the tines or wheels seem to hesitate while
turning, but the engine maintains the same speed.
due to normal stretch and wear on the belt. Adjustment
is needed if the tines or wheels seem to hesitate while
turning, but the engine maintains the same speed.
To adjust the tension on the belt, refer to clutch
adjustment information in “Checking the Clutch
Adjustment” section of the Assembly Instructions. After
belt tension has been adjusted, if the belt is excessively
stretched, you may need to adjust the idler pulley rod.
This can easily be checked. With the engine off and the
clutch control bail disengaged, shift the gear selection
handle to each forward mode. If the indicator bracket
touches the idler pulley rod, (with the clutch control bail
disengaged), then an adjustment is necessary.
adjustment information in “Checking the Clutch
Adjustment” section of the Assembly Instructions. After
belt tension has been adjusted, if the belt is excessively
stretched, you may need to adjust the idler pulley rod.
This can easily be checked. With the engine off and the
clutch control bail disengaged, shift the gear selection
handle to each forward mode. If the indicator bracket
touches the idler pulley rod, (with the clutch control bail
disengaged), then an adjustment is necessary.
•
Disconnect and ground out spark plug wire against
the engine.
the engine.
Use This
Position
First Time
Position
First Time
Transport
Position
Position
Clevis
Pin
Pin
Hairpin
Clip
Clip
Use This
Hole for
Lowest (Shallowest)
Position
Use This Hole for
Highest (Deepest)
Position
Side
Shields
Front
Wing Nut
Wing Nut
Rear
Wing Nut
Wing Nut