White Outdoor RB650 Manual Do Utilizador
13
SECTION 9: OFF-SEASON STORAGE
If the tiller will not be used for a period longer than 30
days, the following steps should be taken to prepare the
tiller for storage.
days, the following steps should be taken to prepare the
tiller for storage.
•
Clean the exterior of engine and the entire tiller
thoroughly. Lubricate the tiller as described in the
lubrication instructions.
thoroughly. Lubricate the tiller as described in the
lubrication instructions.
•
We do not recommend the use of pressure
washers to clean your unit. They may cause
damage to electric components, spindles, pulleys,
bearings or the engine. The use of pressure
washers will result in shortened life and reduce
serviceability.
washers to clean your unit. They may cause
damage to electric components, spindles, pulleys,
bearings or the engine. The use of pressure
washers will result in shortened life and reduce
serviceability.
•
Refer to the engine manual for correct engine
storage instructions.
storage instructions.
•
Wipe tines with oiled rag to prevent rust.
•
Store tiller in a clean, dry area. Do not store next to
corrosive materials, such as fertilizer.
corrosive materials, such as fertilizer.
NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rustproof the equipment. Using a light oil or
silicone, coat the equipment, especially any springs,
bearings and cables.
an unventilated or metal storage shed, care should be
taken to rustproof the equipment. Using a light oil or
silicone, coat the equipment, especially any springs,
bearings and cables.
SECTION 10: TROUBLE SHOOTING GUIDE
NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
Trouble
Possible Cause(s)
Corrective Action
Engine fails to
start
start
Fuel tank empty, or stale fuel.
Throttle control lever not in correct
starting position (if so equipped).
Blocked fuel line.
Dirty aircleaner.
Choke not in ON position.
Spark plug wire disconnected.
Faulty spark plug.
Engine flooded.
starting position (if so equipped).
Blocked fuel line.
Dirty aircleaner.
Choke not in ON position.
Spark plug wire disconnected.
Faulty spark plug.
Engine flooded.
Fill tank with clean, fresh gasoline. Fuel will not last over
thirty days unless a fuel stabilizer is used.
Move throttle lever to start position.
thirty days unless a fuel stabilizer is used.
Move throttle lever to start position.
Clean fuel line.
Refer to the engine manual packed with your unit.
Move switch to ON position.
Connect wire to spark plug.
Clean, adjust gap or replace.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Move switch to ON position.
Connect wire to spark plug.
Clean, adjust gap or replace.
Refer to the engine manual packed with your unit.
Engine runs
erratic
erratic
Unit running on CHOKE.
Spark plug wire loose.
Blocked fuel line or stale fuel.
Spark plug wire loose.
Blocked fuel line or stale fuel.
Vent in gas cap plugged.
Water or dirt in fuel system.
Dirty air cleaner.
Carburetor out of adjustment.
Water or dirt in fuel system.
Dirty air cleaner.
Carburetor out of adjustment.
Move choke lever to OFF position.
Connect and tighten spark plug wire.
Clean fuel line; fill tank with clean, fresh gasoline. Fuel will
not last over thirty days unless a fuel stabilizer is used.
Clear vent.
Drain fuel tank. Refill with fresh fuel.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Connect and tighten spark plug wire.
Clean fuel line; fill tank with clean, fresh gasoline. Fuel will
not last over thirty days unless a fuel stabilizer is used.
Clear vent.
Drain fuel tank. Refill with fresh fuel.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Engine over-
heats
heats
Engine oil level low.
Dirty air cleaner.
Air flow restricted.
Carburetor not adjusted properly.
Dirty air cleaner.
Air flow restricted.
Carburetor not adjusted properly.
Fill crankcase with proper oil.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Adjust carburetor as instructed in separate engine manual.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Adjust carburetor as instructed in separate engine manual.
Tines do not
engage
engage
Foreign object lodged in tines.
Tine clevis pin(s) missing.
Pulley and idler not in correct
adjustment.
Not shifting properly.
Tine clevis pin(s) missing.
Pulley and idler not in correct
adjustment.
Not shifting properly.
Control cable not adjusted properly.
Belt worn and/or stretched.
Belt worn and/or stretched.
Dislodge foreign object.
Replace tine clevis pin(s).
Take unit to authorized service dealer.
Replace tine clevis pin(s).
Take unit to authorized service dealer.
Refer to Controls section of operator’s manual for proper
shifting procedures.
Adjust control cable (see assembly instructions).
Replace belt.
shifting procedures.
Adjust control cable (see assembly instructions).
Replace belt.
Tines skip over
ground
ground
Improper rotation.
Forward rotation should only be used on soil that has
already been tilled, not on virgin soil.
already been tilled, not on virgin soil.
Wheels do not
engage
engage
Clevis pin missing.
Tiller is not being shifted properly.
Tiller is not being shifted properly.
Control cable not adjusted properly.
Belt worn and/or stretched.
Belt worn and/or stretched.
Replace clevis pin.
Refer to Controls section of operator’s manual for proper
shifting procedures.
Adjust control cable (see assembly instructions).
Replace belt.
Refer to Controls section of operator’s manual for proper
shifting procedures.
Adjust control cable (see assembly instructions).
Replace belt.