Whirlpool W10032070 Manual Do Utilizador
8
INSTALLATION INSTRUCTIONS
Unpack Range
1. Do not use oven door handle to lift or move the range.
2. Remove shipping materials, tape and protective film from
range. Keep cardboard bottom under range. Remove oven
racks and parts package from inside oven.
racks and parts package from inside oven.
3. Take 4 cardboard corners from the carton. Stack one
cardboard corner on top of another. Repeat with the other 2
corners. Place them lengthwise on the floor behind the range
to support the range when it is laid on its back. Using 2 or
more people, firmly grasp the range and gently lay it on its
back on the cardboard corners.
corners. Place them lengthwise on the floor behind the range
to support the range when it is laid on its back. Using 2 or
more people, firmly grasp the range and gently lay it on its
back on the cardboard corners.
4. Pull cardboard bottom firmly to remove.
5. Use an adjustable wrench to loosen the leveling legs. Adjust
the leveling legs to the correct height. Leveling legs can be
loosened to add up to a maximum of 1" (2.5 cm). A maximum
of 3/16" (5 mm) is needed to engage the anti-tip bracket.
loosened to add up to a maximum of 1" (2.5 cm). A maximum
of 3/16" (5 mm) is needed to engage the anti-tip bracket.
NOTE: If height adjustment is made when range is standing, tilt
the range back to adjust the front legs, then tilt forward to adjust
the rear legs.
the range back to adjust the front legs, then tilt forward to adjust
the rear legs.
6. Place cardboard or hardboard in front of range. Using 2 or more
people, stand range back up onto cardboard or hardboard.
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
A
A. Cardboard shipping base
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
or serious burns to children and adults.
Install Anti-Tip Bracket
Contact a qualified floor covering installer for the best procedure
for drilling mounting holes through your type floor covering.
for drilling mounting holes through your type floor covering.
If the cabinet opening is wider than specified in the “Location
Requirements” section, adjust the template so the range will be
centered in the cabinet opening.
Requirements” section, adjust the template so the range will be
centered in the cabinet opening.
5. To mount the anti-tip bracket to a wood floor, drill two 1/8"
(3.2 mm) holes at the positions marked on the bracket
template. Remove the template from the floor.
template. Remove the template from the floor.
To mount the anti-tip bracket to a concrete or ceramic floor, use
a 3/16" (4.8 mm) masonry drill bit to drill 2 holes at the positions
marked on the bracket template. Remove the template from the
floor.
a 3/16" (4.8 mm) masonry drill bit to drill 2 holes at the positions
marked on the bracket template. Remove the template from the
floor.
Before moving range, slide range onto shipping base, cardboard
or hardboard.
or hardboard.
1. Remove template from the anti-tip bracket kit (found inside
the oven cavity).
2. Place template on the floor in the cabinet opening so that the
left edge is against the cabinet and the top edge is against
the rear wall, molding or cabinet.
the rear wall, molding or cabinet.
3. Tape template in place.
4. If the countertop is not flush with the cabinet opening edge,
align the template with the overhang.
6. Tap plastic anchors into holes with a hammer.
7. Align the anti-tip bracket holes with the holes in the floor.
Fasten the anti-tip bracket with the screws provided.
Depending on the thickness of your flooring, longer screws may
be necessary to anchor the bracket to the subfloor. Longer
screws are available from your local hardware store.
be necessary to anchor the bracket to the subfloor. Longer
screws are available from your local hardware store.