Westinghouse Two-Light Indoor Flush-Mount Ceiling Fixture 6430000 Manual De Instruções

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires.  These fixtures 

meet all UL specifications.
1.      Turn off power at circuit box to avoid possible electric shock.

2.   Thread mounting screws (A) into mounting bar (B) (see fig. 1) approximately 1/4 inch.

3.   Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).

4.   Identify color coding of fixture wires (see fig. 2).

5.   Connect the black wire from the fixture with the black wire (live wire) from the outlet box by wire 

      connector, and wrap the wire connector with electrical tape for a more secure connection.

6.   Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by 

      wire connector, and wrap the wire connector with electrical tape for a more secure connection.

7.   Partially thread green grounding screw (F) into side hole (G) on mounting bar (B) (see fig.1).

8.   Wrap grounding wire from fixture around green grounding screw stem (F) leaving enough excess 

      wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet 

      box by wire connector (E) (if applicable), then wrap the wire connector (E) with electrical tape for a 

      more secure connection.

9.   Tighten green grounding screw (F). Do not over tighten.

10. Tuck wires inside outlet box (C).

  Warning: This fixture is for indoor use only.
1.   Raise canopy (H) to ceiling allowing mounting screws (A) to protrude through key slots (I) in 

      canopy (H) (see fig. 1).

2.   Rotate canopy (H) clockwise until mounting screws (A) lock into narrow portion of key slots (I). 

      Secure into place with mounting screws (A).

3.   Install lamp(s). Do not exceed recommended wattage.

4.   Raise glass shade (J) to canopy (H) allowing nipple (K) to protrude through opening.

5.   Carefully support glass shade (J) while securing washer (L), hex nut (O), cap (M), and finial (N) to 

      nipple (K).

6.   Turn power back on at circuit box.

W-375

082814

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a 

period of Five Years from purchase date.  This warranty is in lieu of all other warranties expressed or 

implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration 

of components, nor does it cover damages caused through abuse, improper installation, surges in 

electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.

Congratulations on your Westinghouse purchase.  This fixture has been designed to give you many 

years of beauty and service.  For questions and comments, please visit www.westinghouselighting.

com/contact-us.
NOTE: Carefully unpack fixture and parts.  Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

Line art shown may not exactly match the 

fixture enclosed. However, the installation 

instructions do apply to this fixture.

CLEANING AND CARE 

To clean, wipe fixture with soft cloth.  Clean glass with mild soap.  Spray from chemical cleaners can 

discolor the finish of fixture.  Do not use scouring pads, powders, steel wool or abrasive paper to 

clean this fixture.
NOTE  FOR FIXTURES THAT ARE  SOLID BRASS:

Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-

quer which gives maximum protection against the weather.  However, in time the brightness of the 

brass will tarnish, giving way to an authentic old-world brass finish.  To keep your solid brass fixture 

looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-

faces, giving the fixture an extra protective covering.

ORDERING PARTS 

Keep this manual for future reference, and in case replacement parts are needed.  Available parts can 

be ordered from place of purchase.  Use exact wording from diagrams when ordering parts.

FIXTURE

WIRES:

Black

HOUSE

WIRES:

Black

(Hot)

HOUSE

WIRES:

White

(Neutral)

HOUSE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

White

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.  

www.westinghouselighting.com

       , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.           
Used under license by Westinghouse Lighting. 

All rights reserved. 

 

Made in China        

Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de matéri-

aux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se substitue 

à toute autre garantie expresse ou tacite.

 

Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la 

foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages 

survenant suite à une utilisation anormale, une installation impropre, une surtension de courant élec-

trique ou des actes d’un tiers.

 

Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez- 

nous gratuitement au numéro suivant : 1-888-417-6222.

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été 

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces 

y sont avant de mettre l’emballage au rebut (voir fig. 1).

Il est possible que le dessin illustré ici ne 

soit pas la reproduction exacte de l’appareil 

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent 

cependant valables.