Westinghouse Recessed Light Converter 0101100 Manual De Instruções
2
Figure 1
Figure 2
Figure 3
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Westinghouse Lighting Corporation
Philadelphia, PA 19154-1029, U.S.A.
Westinghouse Lighting Corporation
a Westinghouse Electric Corporation licensee;
“Westinghouse” and “You can be sure...if it’s Westinghouse”
are all registered trademarks of Westinghouse Electric Corporation
© 2013 WESTINGHOUSE LIGHTING CORPORATION, INC
Recessed Light Converter
Instruction
M
H
C&D
H
E
G
J
K
C&D
F
INSTALLATION INSTRUCTIONS
1. Make sure the power is off. Remove the lamp (If applicable) from the socket.
2. Thread the socket pigtail (M) into the recessed can socket (Figure 1).
3. Take of the mounting bracket (F) and the washer (I) from the inner/outer sections for channel brace (C/D) by removing the two
1/4" long side screws (H) (Figure 2).
4. Raise the adjustable channel brace (C/D) into the recessed can and slide the inner and outer sections of the channel brace as
wide as possible, so that the both ends of the brace are against the sides of the recessed can, move the locking bar (E) to the
center of the channel brace, then tighten the center screw (G) (Figure 3).
5. Secure the sliding bar to the recessed can, by using the two supplied 1” long self piercing screws (N). By using a power drill and a
5. Secure the sliding bar to the recessed can, by using the two supplied 1” long self piercing screws (N). By using a power drill and a
1/4" hexagon driver, drive the two screws through both sides of the channel brace to the side of the recessed can (Figure 4).
Note: Do not use any other type of screw. These screws are specifically designed for this application. Only two screws are
needed, two extra screws were provided for your convenience.
6. Install the mounting bracket (F) and the washer (I) back onto the channel brace (C/D), by using the two side screws (H) removed
6. Install the mounting bracket (F) and the washer (I) back onto the channel brace (C/D), by using the two side screws (H) removed
from step 3 (Figure 5).
Note: The washer must be used for 5” & 6” can installations; Do not use the washer for 4” can installation.
7. Install the green ground wire with screw (K) to the side of the recessed can using ground screw (J) (Figure 6).
8. Raise the metal cover plate (A), rotate it and make sure the mounting bracket holds the metal cover plate in place (Figure 7).
9. Install your lighting fixture's mounting bar (Q) (Not included, it comes with the lighting fixture purchased separately) on mount
7. Install the green ground wire with screw (K) to the side of the recessed can using ground screw (J) (Figure 6).
8. Raise the metal cover plate (A), rotate it and make sure the mounting bracket holds the metal cover plate in place (Figure 7).
9. Install your lighting fixture's mounting bar (Q) (Not included, it comes with the lighting fixture purchased separately) on mount
ing bracket (F) with two 1/2" long fixture screws (O) (included) (Figure 8). Follow the installation instructions included with your
luminaire to mount onto the recess can converter kit.
10. Insert the lighting fixture wires through the decorative medallion center hole (B), and place the decorative medallion onto the
10. Insert the lighting fixture wires through the decorative medallion center hole (B), and place the decorative medallion onto the
canopy (Figure 9). Note: Decorative medallion is held in place by installed fixture.
11. Make the electrical connection between the pigtail (M) and your fixture's electrical wires, and raise the decorative medallion and
11. Make the electrical connection between the pigtail (M) and your fixture's electrical wires, and raise the decorative medallion and
fixture canopy. Secure the canopy according to your lighting fixture installation instruction (Figure 10).
I
A
F
B
O
Figure 4
N