Alpine IVA-D106R Manual Do Utilizador
55
-EN
Setting Bass Sound Control
Setting item : BASS SOUND CONT.
Touch [
] of BASS SOUND CONT.
The Bass Sound Cont. screen appears.
You can adjust the sound of low frequencies as desired.
Touch [
] or [
] of BASS COMP. to select the desired
mode.
Bass sound is emphasized more as the mode is sequentially
switched as MODE1
switched as MODE1
2
3, offering you vivid low
frequencies.
Select OFF when the setting is not necessary.
Select OFF when the setting is not necessary.
Touch [RETURN] to return to the previous screen.
Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
Set the delay number in the front and rear, and on the
right and left of the desired speaker by touching the
respective [
right and left of the desired speaker by touching the
respective [
] or [
] button.
• Any setting in Bass Focus is applied in time correction, too.
• Touch [RETURN] to return to the previous screen.
• Touch [RETURN] to return to the previous screen.
Speaker Setup
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if Decode mode is switched.
adjustment. The setting is cancelled if Decode mode is switched.
Setting item : SPEAKER SETUP
Select the speaker characteristic by touching [
] or [
]
of the desired speaker setting.
• The Subwoofer can be set only to ON/OFF.
• If the centre speaker is turned “OFF,” the center channel’s audio
• If the centre speaker is turned “OFF,” the center channel’s audio
signals are added to the audio signals output from the front speakers.
• If you set the speaker response to “OFF”, also set the speaker setting
to “OFF” (page 52).
• Perform the setup for all the speakers (“Front,” “Center,” “Rear”
and “Subwoofer”). If not, the sound may not be balanced.
• When centre is set to “OFF”, the setting is ineffective even if centre
is set with this function.
• Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
requirements.
• When using the PRO LOGIC II, if the rear speaker is set to
“LARGE”, then there will be no output from the subwoofer.
• The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Setting of Dolby Digital
Setting item : MULTI CH SETUP
Touch [
] of MULTI CH SETUP.
The MULTI CH SETUP display appears.
Set the items below as you desire.
Set the items below as you desire.
Setting Bass Compressor
Setting Bass Focus
OFF*
1
:
When no speaker is connected.
SMALL:
When a speaker that cannot play low frequencies
(80 Hz or less) is connected.
(80 Hz or less) is connected.
LARGE*
2
: When a speaker that can play low frequencies (80
Hz or less) is connected.
*
1
It is not possible to set the front speakers to “OFF”.
*
2
If the front speakers are set to “SMALL”, the rear and
centre speakers cannot be set to “LARGE.”
centre speakers cannot be set to “LARGE.”