Unigreen TOWED MISTBLOWERS LASER-FUTURA- EXPO series AT STD/TOP - AT BASE Manual Do Utilizador
18 unigreen
5.4
AXIAL ROTOR
Generally the new models of rotors are fitted with 7 vanes made of aluminium
or nylon + fibreglass and the vanes have a variable inclination from 20° to 40°
with step adjustment by 5° (in some cases there are drilled reference discs)
FIG. 20.
The angular movement of all of the vanes, if done correctly, doesn’t change the
dynamic balance of the blower group.
To change the inclination of the vanes (as standard this is set at 35°) proceed
as follows:
a)
or nylon + fibreglass and the vanes have a variable inclination from 20° to 40°
with step adjustment by 5° (in some cases there are drilled reference discs)
FIG. 20.
The angular movement of all of the vanes, if done correctly, doesn’t change the
dynamic balance of the blower group.
To change the inclination of the vanes (as standard this is set at 35°) proceed
as follows:
a)
Remove the protective grill.
b)
Unscrew screws A that hold the spinner (central cover), each vane has two
blocking screws B at the side, one on the right and one on the left. Unscrew the
two screws enough to turn the vane the degrees necessary (replace the drilled
discs when fitted). To make the adjustment easier, there are reference notches
on blocking element C.
c)
two screws enough to turn the vane the degrees necessary (replace the drilled
discs when fitted). To make the adjustment easier, there are reference notches
on blocking element C.
c)
After you have positioned the vane, perform the same operation on the
next one and screw the screws of the first in enough to block it in place.
d)
d)
Repeat the operation on all the vanes and after you’ve checked that all
have the same angle, reassemble the spinner and the protective grill.
The fan is balanced dynamically; the different numbers of washers under the
screws blocking the vanes are for balancing.
You shouldn’t change the position of the washers or add or remove any. Only
tighten down the screws with moderate force as they have an aluminium
thread.
The fan is balanced dynamically; the different numbers of washers under the
screws blocking the vanes are for balancing.
You shouldn’t change the position of the washers or add or remove any. Only
tighten down the screws with moderate force as they have an aluminium
thread.
5.5
CLUTCH
Big aluminium and nylon blowers have a centrifugal type clutch that makes it
possible to engage the fan rotor gradually.
This prevents jerky starts, due to the inertia of the fan rotor, which can have a
negative effect on the transmission.
For the centrifugal clutch to work properly the speed of the power-takeoff
mustn’t be less than 450 rpm, especially if you are using the first gear of the
multiplier.
Generally clutches with shoes/plates made of sintered material with a high
coefficient of friction are fitted, on some low power models rubber clutches may
be fitted.
possible to engage the fan rotor gradually.
This prevents jerky starts, due to the inertia of the fan rotor, which can have a
negative effect on the transmission.
For the centrifugal clutch to work properly the speed of the power-takeoff
mustn’t be less than 450 rpm, especially if you are using the first gear of the
multiplier.
Generally clutches with shoes/plates made of sintered material with a high
coefficient of friction are fitted, on some low power models rubber clutches may
be fitted.
5.6
CANNON BLOWER GROUP
The cannon blower group is equipped with a multiplier similar to the normal
axial blower groups and all of its operating characteristics are the same.
The main difference with respect to the axial blower groups is that the
centrifugal fan rotor is made of galvanised steel, the fan rotors in this type are
fixed and can’t be adjusted, for the clutch see the previous paragraph. This fan
rotor can usually produce a delivery which is much higher with a very high
speed airflow.
The cannon fan is mounted on a thrust block that can be adjusted by hand by
unscrewing the relevant locking screw. This adjustment must be done with the
fan rotor stopped because the high speed of the air make the movement of the
fan dangerous.
axial blower groups and all of its operating characteristics are the same.
The main difference with respect to the axial blower groups is that the
centrifugal fan rotor is made of galvanised steel, the fan rotors in this type are
fixed and can’t be adjusted, for the clutch see the previous paragraph. This fan
rotor can usually produce a delivery which is much higher with a very high
speed airflow.
The cannon fan is mounted on a thrust block that can be adjusted by hand by
unscrewing the relevant locking screw. This adjustment must be done with the
fan rotor stopped because the high speed of the air make the movement of the
fan dangerous.
5.6.1 MANUALLY INCLINABILE HEAD
The cannon blower group can be equipped with a pivoting head (max inclination
180°) adjustable by hand.
The cannon blower group can be equipped with a pivoting head (max inclination
180°) adjustable by hand.
5.6.2 HYDRAULIC DRIVEN HEADS
On request hydraulic pivoting (inclination 90° roughly) and rotating (max rotation
270°) heads are available.
On request hydraulic pivoting (inclination 90° roughly) and rotating (max rotation
270°) heads are available.
5.6.3 HYDRAULIC DRIVES
The cannon fans can be equipped with hydraulic drives: with the cylinder fitted
directly (30° inclination roughly) or a motor with a pinion and chain (180°
inclination roughly).
The cannon fans can be equipped with hydraulic drives: with the cylinder fitted
directly (30° inclination roughly) or a motor with a pinion and chain (180°
inclination roughly).
FIG. 20
drilled reference disc
(only fitted models)