Electrolux OHV Manual Do Utilizador

CONSUMER

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury,

before performing any service or ad-

justments:
1. Be sure throttle is in STOP posi-

tion.

2. Remove safety ignition key.
3. Make sure the augers and all moving

parts have completely stopped.

4. Disconnect spark plug wire from

spark plug and place wire where it

cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”

in the Operation section of this manual.
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge

chute, is provided to direct discharging snow away from

the operator. If the deflector becomes damaged, it should

be replaced.

WARNING: To avoid serious injury,

never operate your snow thrower with

the deflector removed or damaged.

• To change direction and/or distance snow is discharged,

see “TO CONTROL SNOW DISCHARGE” in the Op-

eration section of this manual.

SHEAR BOLTS (See Fig. 22)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger

shaft with a shoulder/shear bolt and hex nut. Should a for-

eign object or ice become lodged in the augers, the shear

bolts are designed to break, preventing damage to any

other components. If one or both augers do not turn when

auger control lever is engaged, check to see if one or both

of the bolts have sheared. To replace the shear bolts:
1. Disengage all controls and move throttle control to

STOP position. Wait for all moving parts to stop.

2. Disconnect spark plug wire from spark plug and place

it wear it cannot come in contact with spark plug.

3. Align hole in auger hub with hole in auger shaft and

install a new 1/4-20 x 2" shoulder/shear bolt. Install

1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original

equipment shear bolts as supplied with your

snow thrower.

4. Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)

capscrew/shear bolts and hex nuts. Should a foreign object

or ice become lodged in the impeller, the capscrews are

designed to break, preventing damage to any other com-

ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared.

To replace the capscrew/shear bolts:

1. Disengage all controls and move throttle control to

STOP position. Wait for all moving parts to stop.

2. Disconnect spark plug wire from spark plug and place

it wear it cannot come in contact with spark plug.

3. Align holes in impeller hub with holes in impeller shaft

and install two (2) new 1/4-20 x 1-5/8" capscrew/shear

bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original

equipment capscrew/shear bolts as supplied

with your snow thrower.

4. Connect spark plug wire to spark plug.

TO REMOVE BELT COVER (See Fig. 23)
1. Remove the two (2) screws securing belt cover to

frame.

2. Remove belt cover.
• Replace belt cover by installing cover and screws and

tighten securely.

TO REPLACE BELTS (See Fig. 24)

BELT

COVER

SCREWS

FRAME

FIG. 23

AUGER

SHAFT

1/4-20 x 2

SHOULDER

/SHEAR BOLT

1/4-20

LOCKNUT

IMPELLER

SHAFT

1/4-20 x 1-5/8

CAPSCREW /

SHEAR BOLT

1/4-20

LOCKNUT

IMPELLER HUB

AUGER

HUB

AUGER

HUB

FIG. 22

For Husqvarna Parts Call 606-678-9623 or 606-561-4983