Furman Sound RackRider RR-131 Folheto
SPECIFICA
SPECIFICA
SPECIFICA
SPECIFICA
SPECIFICATIONS
TIONS
TIONS
TIONS
TIONS
Channels:
RR-131: one; RR-215, RR-231: two
Bands per Channel:
RR-215: 15 (25, 40, 63, 100, 160, 250, 400, 630,1k, 1.6k, 2.5k, 4k, 6.3k, 10k, 16k)
RR-131, RR-231: 31 (20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400,
500, 630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k, 8k, 10k, 12.5k, 16k, 20k)
RR-131, RR-231: 31 (20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400,
500, 630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k, 8k, 10k, 12.5k, 16k, 20k)
Boost/Cut Range:
±6 dB or ±12 dB, switch selectable
Slider Travel:
20 mm with center detent
Input Connections:
Active balanced XLR and ¼" TRS; unbalanced RCA
Impedance:
Input: 20 k
Ω
balanced; 15 k
Ω
unbalanced; Output: Less than 600
Ω
Maximum Levels:
Input: +18 dBV; Output: +16 dBV
Signal to Noise Ratio:
93 dB at 1 kHz
Distortion:
.02% THD, 1 kHz, all sliders at center
Frequency Response:
20 Hz to 50 kHz, +0, -3 dB, all sliders at center
High Pass Filter:
RR-131, RR-231: 10 Hz To 250 Hz Variable; RR-215, 40 Hz fixed; 12 dB/octave
Low Pass Filter:
RR-131, RR-231: 3 kHz To 50 kHz Variable; RR-215: 16 kHz fixed; 12 dB/octave
Dimensions (W X D X H):
RR-215, RR-131: 19" X 8.66" X 1.75"; RR-231: 19" X 8.66" X 3.5"
Weight:
RR-215, RR-131: 5.22 lbs (2.9 kg); RR-231: 9.36 lbs (5.2 kg)
Power Requirements:
100-120 VAC, 60 Hz, or 200-240 VAC, 50 Hz, switch selectable; 15 watts
Safety Agency Approvals:
CE, TUV, EMC. Pending: NRTL
(unbalanced). The extra outputs may be used if, for example,
a signal split is needed to feed both a tape recorder and a PA
system.
a signal split is needed to feed both a tape recorder and a PA
system.
CONTROLS AND INDICA
CONTROLS AND INDICA
CONTROLS AND INDICA
CONTROLS AND INDICA
CONTROLS AND INDICAT
T
T
T
TORS
ORS
ORS
ORS
ORS
Power on-off
Range: Allows selection of ±6 dB or ±12 dB boost or cut.
Color-coded LED’s indicate the range selected.
Bypass: Toggles the EQ between IN and OUT (bypassed).
A yellow LED glows to indicate Bypass.
Low Pass Filter: Decreases the higher frequencies. Useful
in reducing hiss or sibilance. The filtering range is
continuously adjustable from 3 kHz up to 50 kHz.
continuously adjustable from 3 kHz up to 50 kHz.
High Pass Filter: Decreases the lower frequencies, to
combat rumble, footsteps, wind noise, etc. Continuously
adjustable from 10 Hz to 250 Hz.
adjustable from 10 Hz to 250 Hz.
Level Control: This control may be used to compensate
for any changes in volume caused by the EQ settings.
Clip LED: Indicates a distortion-causing overload. Adjust
the Level control to compensate for clipping.
EQ Sliders: These sliders allow boost or cut of either ±6
dB or ±12 dB (depending on the setting of the Range switch)
over a narrow frequency band.
over a narrow frequency band.
Ground Lift: Fights hum or buzz by separating the signal
and chassis grounds.
W
W
W
W
WARRANTY INFORMA
ARRANTY INFORMA
ARRANTY INFORMA
ARRANTY INFORMA
ARRANTY INFORMATION
TION
TION
TION
TION
The RackRider RR-Series Graphic Equalizers are
protected by a limited ninety (90) day warranty covering
manufacturing defects. Warranty service is provided by
Furman at the address below.
manufacturing defects. Warranty service is provided by
Furman at the address below.
Rear Views, RR-215, RR-131, RR-231
3-0110
963002-2751