Friedrich PDXRC Folheto
920-172-00 (2-08)
Preparing unit for remote control use
NOTE: The remote control operation requires the control
panel door of the PTAC to remain open or be removed
from the unit. If electing to use the fi ll piece, follow Steps
1-4. Otherwise, proceed straight to Step 5.
1) Remove the control panel door from the front grille by
panel door of the PTAC to remain open or be removed
from the unit. If electing to use the fi ll piece, follow Steps
1-4. Otherwise, proceed straight to Step 5.
1) Remove the control panel door from the front grille by
unhinging it from the grille. This is done by pushing
back on the top portion of the door until the door is
released from the hinges.
back on the top portion of the door until the door is
released from the hinges.
2) Remove the front grille from the unit.
3) Screw the fi ll piece to the unit using the screws provid-
3) Screw the fi ll piece to the unit using the screws provid-
ed into the two screw holes above the control panel.
4) Reattach the front grille.
5) Turn on the PTAC unit
6) Put batteries in the remote
7) The remote control is now ready for operation.
8) Your unit should come already enabled to receive the
5) Turn on the PTAC unit
6) Put batteries in the remote
7) The remote control is now ready for operation.
8) Your unit should come already enabled to receive the
remote signal. If after all the steps are done and your
unit does not respond to remote signal, hold the temp
unit does not respond to remote signal, hold the temp
and the temp
buttons simultaneously for three
seconds, or until the display window shows "E" to
enable the remote.
enable the remote.
Operating Instructions
HAND HELD REMOTE CONTROL
For Use With Packaged Terminal Units
Please read these instructions completely before
attempting installation.
NOTE: This kit is for use with PD model Friedrich
PTAC units with SD or later suffi xes. For example:
PDE09K3SD. This kit will not work with prior models.
attempting installation.
NOTE: This kit is for use with PD model Friedrich
PTAC units with SD or later suffi xes. For example:
PDE09K3SD. This kit will not work with prior models.
Model PDXRC
PDXRC
Remote
Control
Remote
Control
Low
Te
TT mp
m era
rr tu
tt r
uu e
rr
Cool
Po
P we
w
w r
Co
CC ole
ll r
Fa
FF n
On
O ly
l
Wa
W
W rm
rr er
He
HH at
Fa
FF n
Hi
HH g
ii h
g
Fa
FF n
Remote Control Operation
POWER - Press the Power button once. The unit will automat-
ically turn on in the mode and fan speed it was last left on.
ically turn on in the mode and fan speed it was last left on.
To set mode of operation
COOL - Press the Cool button to automatically switch the
operating mode to COOL.
HEAT - Press the Heat button to automatically switch the
operating mode to Heat.
FAN ONLY - Press the Fan Only button if you want to run
the fan only.
COOLER - Press the Cooler button to raise the tempera-
ture setting one degree.
WARMER - Press the Warmer button to lower the tem-
perature setting one degree.
operating mode to COOL.
HEAT - Press the Heat button to automatically switch the
operating mode to Heat.
FAN ONLY - Press the Fan Only button if you want to run
the fan only.
COOLER - Press the Cooler button to raise the tempera-
ture setting one degree.
WARMER - Press the Warmer button to lower the tem-
perature setting one degree.
To adjust fan speed
Low Fan - Press the Low Fan button to adjust the fan
speed to low.
High Fan - Press the High Fan button to adjust the fan
speed to high.
speed to low.
High Fan - Press the High Fan button to adjust the fan
speed to high.
Fill Piece Installation
This kit contains............................. Qty
1. Installation instructions ................ 1
2. Remote control ............................ 1
3. AAA batteries............................... 2
4. Fill piece ...................................... 1
5. Screws #8 x 3/8 ........................... 2
1. Installation instructions ................ 1
2. Remote control ............................ 1
3. AAA batteries............................... 2
4. Fill piece ...................................... 1
5. Screws #8 x 3/8 ........................... 2