Auto Page CPX-2300 Folheto

Car-Pro 

 

By: 

Professional Vehicle Security 

 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 

 
 
 
 

 

               

5. Red wire: to constant battery +12v 

7. Black wire: Ground to vehicle 

 

8, Orange wire: 200 mA Ground output when arm

 

10. White wire: Parking light relay output

 

6. Brown wire: Positive output to siren 

9. Red/White wire: Parking light relay power input 

 

4. Yellow wire: To Ignition switch + 12V 

3. Green wire: Negative door trigger input 

2. Violet wire: Positive door trigger input 

1. Blue wire: Instant trigger ground input 

 

 

 

 

 From ignition switch

12V 

12V 

To ignition  
switch +12v

 

 

 
 

A.  TRANSMITTER CODE LEARNING:  
Note: This security system will only retain the last 4 remote transmitters programmed. If the 
transmitter memory is exceeded, the security system will start deleting transmitters from memory in 
chronological order. 
1. 

Disarm the system. 

2. 

Open the Door and keep the door open 

3. 

Turn the ignition key “ OFF / ON “ 6 times, keep at “ON” position at 6

th

 time switching 

4. 

Within 15 seconds press & hold any button for transmitter code learning, a long chirp confirm 
transmitter programmed. 

5. 

Apply steps 4 – 5 to program 2

nd

, 3

rd

 and 4

th

 transmitter.   

Exit: Turn the ignition off, 3 long chirps confirm exit. 
 
B.  FEATURE PROGRAMMING  
1. 

Disarm the system. 

2. 

Open the Door and keep the door open.  

3. 

Turn the ignition key “ OFF / ON “ 3 times stay in on position. (3 chirps to confirm in 
programming mode)  

4. 

Within 15 seconds press button “ I + II “ to select the feature which you want to program. See 
the features programming table below to select the desired features, which you want to 
program. Note the number of siren chirps to confirm the selected feature(s).  

5. 

Press the button “ I “ or “ II “ on the transmitter to enable or disable the specific feature.  

6. 

Repeat steps 4 - 5 for any other features you wish to program.  

 

Number of pressing 
button I + II & chirps 

Program feature 

Press button “ I “ 

/ one long chirp 

Press button “ II “ 

/ Two long chirps 

1 

    Time for door lock 

0.9 sec. 

3.5 sec. 

2 

     Passive Door Lock 

Disable 

Enable 

3 

     Ignition lock 

Enable 

Disable 

4 

    Anti car-jacking 

Disable  

Enable  

5 

    Door Ajar Warning 

Enable  

Disable  

Exit: Turn the ignition off, or close the door, 3 long chirps confirm exit.  
 
C. PASSWORD SETUP:  
1. 

Disarm the system. 

2. 

Open the Door and keep the door open 

3. 

Turn the ignition key “ OFF / ON” 9 times for “New Password Pin Code Setting” and keep at 
“ON” position at 9

th

 time switching.   

4. 

After 2-second pause, the siren will chirp 9 times to confirm entry.  

5. 

Within 15 seconds, begin to enter your chosen 1 – 9 digit by pressing and releasing the 
transmitter button “I” from 1-9 times 

6. 

Press button “ II ” to get out of password setup mode, corresponding to the new password code 
report by siren chirp confirmation. 

Note: Default setting of password code from the factory is “ 1”.  

 
 
 
 
 
 
 
 

oooo

Blue (-) 200mA Unlock

Green (-) 200mA Lock

H1: 10 pin main harness

H2: 3-pin sensor harness

H3: 2-pin LED harness

H4: 3-pin door lock harness