Lucas Industries LPT-PR0312 Manual Do Utilizador

The stencil board guide provides a sleeve for the
router bit so that the router can move easily within
the stencil guide (Fig. 10/11).

To install the stencil board loosen the two screws
in the base. Drop in the stencil board guide and
refasten the two screws.

Clamp or nail the stencil to the work piece, then
slide the stencil while simultaneously moving the
tool (Fig. 12).

Always unplug the tool before cleaning and
performing any maintenance. After using, clean
dust from the tool before storing in a dry, cool
place.

To clean the tool casing, use only a damp (not
wet) cloth with mild soap if required. Do not use
solvents. Do not allow water to enter the tool.

Check the carbon brushes for wear and replace if
worn down to a thickness of 6mm/1/4”. Always
replace both brushes simultaneously (Fig. 13).

To replace brushes, remove the plastic brush
holder cover with a slotted screwdriver. Remove
the old brushes and thoroughly clean out the
brush apertures. Replace with new brushes and
then screw the brush cover back in. Do not over
tighten (Fig. 14).

Note: it will be necessary to completely unscrew
and remove the upper limit-setting knob on the
right side of the router to access the brush cover
on that side. To do this, lock (push down on) the
router height locking lever before unscrewing and
removing the upper limit setting knob. When done,
reverse the above procedure.

Main voltage  

V 240

Main frequency     

Hz 50

Power input              w 1800

No load speed

min 22000

Fig. 12

Fig. 13

Fig. 14

No.

Part Name

Qty

No.

Part Name

1

Pan Head Screw

2

45

Switch Safety Button

2

Tall cap

1

46

Trigger Switch

3

Brush housing

2

47

Switch Compartment Housing Cover

5

Housing

1

48

Housing Screw

6

Name Plate

1

49

Pin 

7

Stator

1

50

Spring

8

Shield

1

51

Base Module

9

Bearing 629

1

52

Screw M5x10

10

Insulation Washer

1

53

Plastic Shield

11

Motor

1

54

Screw M4x10

12

Fan 1

55

Screw 

M5x10

13

Bearing Support

1

56

Base Plate

14

Bearing 6004

1

57

3-Tier Safety Stop

15

Left Handle

1

58

Nut for Hexagon Socket HD

16

Motor Support

1

59

Screw for Hexagon Socket HD

17

Spring

1

60

Spring

18

Brake Knob Release Button

1

61

Screw M6x30

19

Screw M5x40

4

62

Nut for Hexagon Socket HD

20

Collet Chuck

1

63

Screw for Hexagon Socket HD

21

Collet Sleeve

1

64

Nut for Hexagon Socket HD

22

Screw M5x40

2

65

Screw for Hexagon Socket HD

23

Right Handle

1

66

Spring

24

Spring

1

67

Screw M5X10

25

Clamping Screw

1

68

Upper Limit Setting Knob

26

Router Height Locking Lever

1

71

Nylon Nut

27

Hexagon Socket HD Screw

1

73

Cover Plate

28

Shaft Lock Button Cap

1

A01 

Straight Line Guide

29

Retaining Ring

1

A02

Stop Setting Wrench

30

Shaft Locking Pin

1

A03 

Collet Wrench

31

Spring

1

A04

Stencil Board Guide

32

Brake Knob Screw 

1

A05

Straight Router Bit

33

Screw M4x10

4

A06

Collet Adapter

34

ScrewM5x45

2

A07

3/8” Collet Adapter

35

Brush Cover

2

A08

Screw M6x12

36

Carbon Brush & Spring Assembly

2

A09

Spring Washer 6

37

Cord Shield

1

A10

Flat Washer 6

38

Clip

1

A11

Base Module Guide Mount

39

Screw ST4.2x16

2

A12

Trimming Screw

40

Cord

1

A13

Trim Guide with Roller

41

Bearing Housing

1

42

Screw ST4.2x16

2

Plunge Router manual  9/7/07  16:14  Page 7