Dacor SGM466B Guia Da Instalação

a soap and water solution.

Do not use a flame to check

for leaks. After verifying that

there are no gas leaks, turn off

the gas supply to the cooktop

by turning the gas shut-off

valve to the off position. Leak

testing of the appliance shall

be conducted according to the

manufacturer’s instructions.

6. For LP gas installations, the

LP gas tank must have its own

high-pressure regulator. This

is in addition to the pressure

regulator supplied with the

cooktop.

Attach the gas pressure regulator (included with

the cooktop) to cooktop pipe nipple inlet. For

tight installations, the regulator may be installed

upstream from the pipe nipple, anywhere

between the shut-off valve and the cooktop.

Install a gas shut-off valve (not included with

the cooktop) in the main gas supply line in an

accessible location near the cooktop. Complete

connection of the gas supply to the cooktop

by installing 1/2 inch flexible gas line (not

included with the cooktop) between the pressure

regulator and the shut-off valve.

IMPORTANT:

To prevent damage to the gas

pressure regulator, install the

regulator only after the cooktop

is mounted in its permanent

position. Ensure that the arrow

on the regulator points in the

direction of the gas flow towards

the cooktop.

Installing the Burner and Grill

Components

WARNING:

Never attempt to operate the

cooktop with any of the burner

rings, burner caps, grates, or grill

components removed.

SGM Burner Components

Remove the brass burner rings, porcelain burner

caps, and porcelain grates from their shipping

packages. Place each burner ring onto its

corresponding burner base, being certain that

the five alignment tabs slide into the matching

notches in the base. Set each porcelain burner

cap on top of its corresponding burner ring.

Place each grate onto the cooktop, being certain

that the rubber feet are positioned in the locating

dimples.

Grill Components

Remove the grill components from inside

the main carton. Remove all of the packing

materials from the Grill, U-burner, Heat Control

Channels, Grease Control Box and the Drip

Pans.

Begin your set up by placing the Drip Pans

inside on the bottom of the open grill burner

box area, using the dimples to locate the Drip

Pan. Next, slip the open end of the U-burner

onto the gas stub located in the front inside of

the grill burner box, and insert the bracket on

to opposite end of the U-burner into the slot

located on the Grease Control Box.

Proceed to install the Heat Control Channels,

which sit on top of four pins at the inside front

and back of the grease control box. Finally, set

the grill in place on the top of the cooktop.

Grate

Burner Cap

Burner Ring

Top Frame

Burner Head (Fixed)

SGM Burner Components

NOTE:

The U-burner is adjusted at the

factory and does not require

any field adjustment for proper

function.
Electrical Connection

WARNINGS:

1. Ensure that the power supply

is disconnected before

proceeding.

2. Verify that the power supply

matches the ratings found on

the appliance data plate before

proceeding.

3. The complete appliance must

be properly grounded at all

times when electrical power is

applied.

4. Do not ground the appliance

with the neutral (white) house

supply wire. A separate

ground wire must be utilized.

5. If aluminum house supply

wiring is utilized, splice the

appliance copper wires to the

aluminum house wiring using

special connectors designed

and agency-certified for

joining copper and aluminum.

6. Follow the connector

manufacturer’s recommended

procedure carefully. Improper

connection can result in a fire

hazard!

Verifying Proper Operation

WARNINGS:

1. If the cooktop fails to operate

properly, ensure that the

electrical power supply and

gas supply are turned on and

that all installation steps have

been carefully followed. Call

a qualified service technician

if the cooktop still does not

operate properly.

2. The cooktop and shut-off

valve must be disconnected

from the gas supply piping

during any pressure testing

exceeding 1/2 pound per

square inch (3.5 kPA).

3. The cooktop must be isolated

from the gas supply piping

by closing the shut-off valve

during any pressure testing at

or below 1/2 pound per square

inch (3.5 kPA).

Before beginning the test procedure, ensure

that the gas supply is turned off at the shut-off

valve, all cooktop control valves are in the “OFF”

position, and all burner rings, burner caps, and

grates are properly positioned on the cooktop.

SGM Models

Rotate one knob at a time counterclockwise to

the “HIGH” position. Verify that all ignitors spark

continuously, then return the knob to the “OFF”

position. Repeat for all knobs.

Turn on the main gas supply to the cooktop by

opening the gas shut-off valve. Test each burner

separately by pressing and turning one control

knob at a time counterclockwise to the “HIGH”

position. On the SGM models, all ignitors will

spark simultaneously, but only the burner with

gas flowing to it will ignite. On the PGM model,

only the selected burner will spark. (It will take

approximately four seconds for ignition to occur,

at which time all ignitors will stop sparking. If

ignition does not occur within four seconds,

Plug the three-prong plug from the appliance

into the properly grounded and polarized wall

receptacle.

Off Position

Knob Position

Indicator

(Polished Surface)

Burner

Designation

Light & High

Position

Area of

Operation

Low

Position

Logo on Front

Knob Only

SGM Burner Control Valve