Vigo Industries VGT050RBRND Guia De Especificação
3
MAINTENANCE
REQUIRED TOOLS
IMPORTANT POINTS
SAFETY TIPS
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all
parts are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
Prior to installation please read the instructions thoroughly, confirm that all
parts are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
Adjustable wrench
Groove joint pliers
Plumber's putty
Pipe tape
Flat screwdriver
Plumber's putty
Pipe tape
Flat screwdriver
FAUCET
2. CONNECT FLEXIBLE HOSES
TO THE BRASS PIPES.
TO THE BRASS PIPES.
1. SHUT OFF WATER SUPPLY.
REMOVE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
REMOVE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
SURFACE IN PREPARATION FOR
THE NEW FAUCET. FLUSH WATER
CONNECTION AT HOME TO MAKE
SURE NO DEBRIS IS STUCK IN THE
LINE.
THE NEW FAUCET. FLUSH WATER
CONNECTION AT HOME TO MAKE
SURE NO DEBRIS IS STUCK IN THE
LINE.
4
4. CONNECT FLEXIBLE HOSES TO THE
COLD AND HOT WATER SUPPLY.
5. AFTER INSTALLATION IS COMPLETE TURN ON
THE WATER SUPPLY VALVES AND ALLOW BOTH
THE WATER SUPPLY VALVES AND ALLOW BOTH
HOT AND COLD WATER TO RUN AT LEAST ONE
MINUTE EACH. WHILE WATER IS RUNNING, CHECK
FOR LEAKS, ESPECIALLY AT HOOK-UPS TO
SUPPLY LINES. TIGHTENING NUTS SLIGHTLY WILL
STOP ANY MINOR LEAKS.
MINUTE EACH. WHILE WATER IS RUNNING, CHECK
FOR LEAKS, ESPECIALLY AT HOOK-UPS TO
SUPPLY LINES. TIGHTENING NUTS SLIGHTLY WILL
STOP ANY MINOR LEAKS.
3. PLACE NEW FAUCET IN THE POSITION
ON THE SINK. FROM UNDER THE SINK,
PUT GASKET AND PLATE AND THREAD
NUT ONTO THE PIN. TIGHTEN THE NUT.
PLACE SET SCREWS IN TO THE NUT
AND TIGHTEN THEM.
ON THE SINK. FROM UNDER THE SINK,
PUT GASKET AND PLATE AND THREAD
NUT ONTO THE PIN. TIGHTEN THE NUT.
PLACE SET SCREWS IN TO THE NUT
AND TIGHTEN THEM.
3
GASKET
LOCK NUT
SET
SCREWS
SCREWS
2
PLATE
TWO FLEXIBLE
HOSE
Be sure to shut off water supply prior to installation.
Protect your eyes with safety glasses when cutting or soldering water
Protect your eyes with safety glasses when cutting or soldering water
supply lines
Cover your drain to avoid losing parts.
Cover your drain to avoid losing parts.
Prior to beginning installation, turn off the cold and hot water lines and open the hot
and cold knobs on the old faucet to release build-up pressure.
and cold knobs on the old faucet to release build-up pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use one
wrench to anchor the fitting and a second wrench to tighten the nut one additional
turn. Connections that are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your local hardware or
wrench to anchor the fitting and a second wrench to tighten the nut one additional
turn. Connections that are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
All installations can vary depending on how your previous faucet was installed. Not
all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull and/or damage
cleaners, steel wool and harsh chemicals as these will scratch, dull and/or damage
the finish and/or product and void your warranty.
1
ASSEMBLY
PACKAGE CONTENTS