Vigo Industries VGT861 Guia De Especificação
3
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all
parts are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
Prior to installation please read the instructions thoroughly, confirm that all
parts are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
2. CONNECT PIPES WITH COLD AND HOT WATER TO THE
MIXER USING TEFLON TAPE.
3. SECURE MIXER TO THE WALL.
4. CONNECT SPOUT TO THE MIXER USING THE SUPPLIED WASHER.
SECURE WASHER BEHIND THE THREADED PORTION
OF THE SPOUT FOR SPACING. THREAD THE SPOUT SO THE
TIP FACES DOWN MAKING SURE NOT TO OVER TIGHTEN THE SPOUT TO
THE MIXER.
SECURE WASHER BEHIND THE THREADED PORTION
OF THE SPOUT FOR SPACING. THREAD THE SPOUT SO THE
TIP FACES DOWN MAKING SURE NOT TO OVER TIGHTEN THE SPOUT TO
THE MIXER.
NOT INCLUDED.
PLEASE CONSULT
PLEASE CONSULT
A QUALIFIED
LICENSED
PLUMBER.
PLUMBER.
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and
harsh chemicals as these will scratch, dull, and/or damage the finish and/or product
cleaners, steel wool and
harsh chemicals as these will scratch, dull, and/or damage the finish and/or product
void your warranty.
Be sure to shut off water supply prior to installation.
Protect your eyes with safety glasses when cutting or soldering water
Protect your eyes with safety glasses when cutting or soldering water
supply lines
Cover your drain to avoid losing parts.
Cover your drain to avoid losing parts.
Prior to beginning installation, turn off the cold and hot water lines and open the hot
and cold knobs on the old faucet to release build-up pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use one
wrench to anchor the fitting and a second wrench to tighten the nut one additional
turn. Connections that are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
All installations can vary depending on how your previous faucet was installed. Not
all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
When installing your new faucet, turn the connector nuts finger-tight, then use one
wrench to anchor the fitting and a second wrench to tighten the nut one additional
turn. Connections that are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
All installations can vary depending on how your previous faucet was installed. Not
all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Adjustable wrench
Groove joint pliers
Plumber's putty
Pipe tape
Phillips and flat screwdrivers
Plumber's putty
Pipe tape
Phillips and flat screwdrivers
5. ATTACH HANDLE.
COLD
WATER
WATER
SPOUT
HOT WATER
HANDLE
WASHER
MAINTENANCE
REQUIRED TOOLS
IMPORTANT POINTS
SAFETY TIPS
INSTALLATION
ASSEMBLY
PACKAGE CONTENTS
1. SHUT OFF WATER SUPPLY.
REMOVE THE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
REMOVE THE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
SURFACE IN PREPARATION FOR
THE NEW FAUCET. FLUSH WATER
CONNECTION AT HOME TO MAKE
SURE NO DEBRIS IS STUCK IN
THE LINE.
THE NEW FAUCET. FLUSH WATER
CONNECTION AT HOME TO MAKE
SURE NO DEBRIS IS STUCK IN
THE LINE.
1
6. AFTER INSTALLATION IS COMPLETE TURN ON
THE WATER SUPPLY VALVES AND ALLOW BOTH
HOT AND COLD WATER TO RUN AT LEAST ONE
MINUTE EACH. WHILE WATER IS RUNNING,
CHECK FOR LEAKS, ESPECIALLY AT HOOK-UPS
TO SUPPLY LINES. TIGHTENING NUTS SLIGHTLY
WILL STOP ANY MINOR LEAKS.
THE WATER SUPPLY VALVES AND ALLOW BOTH
HOT AND COLD WATER TO RUN AT LEAST ONE
MINUTE EACH. WHILE WATER IS RUNNING,
CHECK FOR LEAKS, ESPECIALLY AT HOOK-UPS
TO SUPPLY LINES. TIGHTENING NUTS SLIGHTLY
WILL STOP ANY MINOR LEAKS.