Vigo Industries VG15215 Ilustrações Dimensionais

3

Your new faucet is designed for years of trouble-free  performance.

Keep it looking new by cleaning it periodically with a soft  cloth. Avoid abrasive
cleaners, steel wool and harsh  chemicals as these will scratch, dull, and/or

damage the  finish and void the warranty.

MAINTENANCE

ASSEMBLY

REQUIRED TOOLS

Adjustable wrench
Allen key - supplied (to remove cartridge if needed)

Plumber's putty - optional
Pipe tape
Flat screwdrivers

SAFETY TIPS

If you use soldering for the installation of the faucet,  the seats, cartridges and

washers will have to be  removed before using flame. Damage caused by

improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting  or soldering water supply
lines.

IMPORTANT POINTS

Prior to beginning installation, turn off the cold and hot  water lines and open the
hot and cold knobs on the old  faucet to release pressure.

When installing your new faucet, turn the connector nuts  finger-tight, then use
one wrench to anchor the fitting and  a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of  the system and

potentially cause product failure which could lead to water damage.

Wrap all threaded connections with pipe tape available  at your local hardware or

plumbing supply store. Always  wrap in a clockwise direction.
Not all necessary supplies to install  your faucet are included, however, they are
available  wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the

warranty.

INSTALLATION

Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts

are included and visually inspect the unit for any defects.

If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.

4

3

5

2

1

1.   SHUT OFF WATER  SUPPLY. REMOVE THE  OLD FAUCET

AND  FLEXIBLE HOSES. CLEAN  SINK SURFACE WITH A NON
ABRASIVE CLEANER IN PREPARATION FOR THE  NEW FAUCET.

!

2. THREAD FEMALE END OF METAL BRAIDED HOSE TO THE

FAUCET (2).

7. AFTER INSTALLATION IS COMPLETE,   TURN ON THE WATER
SUPPLY AND  ALLOW BOTH HOT AND COLD WATER TO  RUN
SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO
VIEW THE CONNECTIONS AT THE MALE AND FEMALE FLEXIBLE
HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER BACK
TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY.
TIGHTENING NUTS SLIGHTLY MAY STOP ANY MINOR LEAKS.

6. ATTACH THE  FEMALE CONNECTIONS OF THE  FLEXIBLE
HOSES TO THE  COLD AND HOT WATER  SUPPLY .

5. (IF NOT DONE ALREADY) ATTACH SPRAYER TO FEMALE
CONNECTION OF SPRAYER HOSE BY HAND AND TIGHTEN
UNTIL SECURE. MAKE SURE THE BLACK WASHER IS SEATED
AND INSTALLED PROPERLY.

!

3. POSITION THE FAUCET IN THE COUNTERTOP HOLE, FROM
BENEATH THE COUNTERTOP HOLE ASSEMBLE THE PLASTIC
HOLDER, RUBBER RING, AND METAL RING IN THE ORDER
DEPICTED IN THE DIAGRAM. THEN THREAD METAL NUT ONTO
HOLLOW PIN. TIGHTEN THE METAL NUT UNTIL FAUCET IS
SECURE.

4. SCREW SPRAY HOSE  TO THE COPPER PIN (THE LONGEST

PIN). MAKE SURE TO HAVE A TIGHT SEAL USING ADJUSTABLE

WRENCH. ATTACH SUPPLIED COUNTERWEIGHT TO THE HOSE.

NUT

STABILIZES FAUCET
UNDER COUNTERTOP

!

!

FAUCET

ASSEMBLY

COUNTERWEIGHT

TWO METAL

BRAIDED HOSES

RUBBER
RING

METAL
RING

PLASTIC
HOLDER

ALLEN KEY (REMOVES

HANDLE TO ACCESS
CARTRIDGE

NUT