Vigo Industries VG15206 Ficha De Características

3

Your new faucet is designed for years of trouble-free  performance.

Keep it looking new by cleaning it periodically with a soft  cloth. Avoid abrasive
cleaners, steel wool and harsh  chemicals as these will scratch, dull, and/or

damage the  finish and void the warranty.

MAINTENANCE

ASSEMBLY

REQUIRED TOOLS

Adjustable wrench
Allen key - supplied (to remove cartridge if needed)

Plumber's putty - optional
Pipe tape
Flat screwdrivers

SAFETY TIPS

If you use soldering for the installation of the faucet,  the seats, cartridges and

washers will have to be  removed before using flame. Damage caused by

improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting  or soldering water supply
lines.

IMPORTANT POINTS

Prior to beginning installation, turn off the cold and hot  water lines and open the
hot and cold knobs on the old  faucet to release pressure.

When installing your new faucet, turn the connector nuts  finger-tight, then use
one wrench to anchor the fitting and  a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of  the system. and

potentially cause product failure which could lead to water damage.

Wrap all threaded connections with pipe tape available  at your local hardware or

plumbing supply store. Always  wrap in a clockwise direction.
Not all necessary supplies to install  your faucet are included, however, they are
available  wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the

warranty.

1.   SHUT OFF WATER  SUPPLY.
REMOVE THE  OLD FAUCET AND
FLEXIBLE HOSES. CLEAN  SINK

SURFACE WITH A NON ABRASIVE
CLEANER IN PREPARATION FOR
THE  NEW FAUCET.

2. REMOVE METAL NUT,  RUBBER RING,
AND METAL  RING  FROM THE FAUCET.
ATTACH METAL BRAIDED HOSES TO
THE FAUCET.

3. POSITION THE FAUCET IN THE 1 3/8"
COUNTERTOP HOLE, FROM BENEATH THE
COUNTERTOP HOLE ASSEMBLE THE
PLASTIC HOLDER, RUBBER RING, AND
METAL RING IN THE ORDER DEPICTED IN
THE DIAGRAM. THEN THREAD METAL NUT
ONTO HOLLOW PIN. TIGHTEN THE METAL
NUT UNTIL FAUCET IS SECURE.

3

2

1

METAL NUT

4. IF SPRAY HOLDER IS NOT ATTACHED,
ATTACH THE  SPRAY  HOLDER AND
SPRAY HOSE TO THE FAUCET  AND
TIGHTEN SCREW UNTIL SPRAY HOLDER

IS SECURE.

5. FEED SPRAY HOSE THROUGH SPIRAL NECK ENSURING THE FEMALE SPRAYER
CONNECTION IS POSITIONED TOWARD TOP OF SPIRAL NECK. ATTACH MALE SPRAYER
CONNECTION TO TOP OF FAUCET BODY WITH ADJUSTABLE WRENCH UNTIL TIGHT.
SEAT SPIRAL NECK INTO SPRAY HOLDER AND FIRMLY PRESS DOWN UNTIL SECURE.

6

7. ATTACH THE  FEMALE
CONNECTIONS OF THE  METAL
BRAIDED HOSES TO THE  COLD
AND HOT WATER  SUPPLY .

8. AFTER INSTALLATION IS COMPLETE,   TURN ON THE WATER SUPPLY AND  ALLOW BOTH
HOT AND COLD WATER TO  RUN SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO VIEW THE CONNECTIONS AT
THE MALE AND FEMALE FLEXIBLE HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER
BACK TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY. TIGHTENING NUTS SLIGHTLY
MAY STOP ANY MINOR LEAKS.

7

INSTALLATION

Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts

are included and visually inspect the unit for any defects.

If you have any questions please contact our Technical Support Department
before proceeding with installation.

6. ATTACH SPRAYER TO FEMALE CONNECTION OF SPRAYER
HOSE BY HAND AND TIGHTEN UNTIL SECURE.

!

4

STABILIZES FAUCET
UNDER COUNTERTOP

!

!

!

SPRAY WASHER

FAUCET ASSEMBLY

NUT

PLASTIC
HOLDER

ALLEN

KEY

TWO

FLEXIBLE
HOSES

RUBBER
RING

METAL
RING

WRENCH