Thermador SGS305FS Instrução De Instalação
English 5
Prepare the Countertop
Cut out the countertop per the dimensions shown in
“Cabinet Requirements” on page 3.
“Cabinet Requirements” on page 3.
Some solid surface materials, such as Surell™ and
Corian®, require different cutting methods. Consult with the
solid surface manufacturer for the correct cutting method
needed. Apply heat reflective tape such as Scotch
Aluminum Foil Tape #425 or #427 (not included) around
the cutout so that it folds over on the top and sides. Do not
wrap the tape underneath the cooktop. Be sure the tape
extends beyond the outermost flange of the cooktop. All
corners should be covered with tape.
Corian®, require different cutting methods. Consult with the
solid surface manufacturer for the correct cutting method
needed. Apply heat reflective tape such as Scotch
Aluminum Foil Tape #425 or #427 (not included) around
the cutout so that it folds over on the top and sides. Do not
wrap the tape underneath the cooktop. Be sure the tape
extends beyond the outermost flange of the cooktop. All
corners should be covered with tape.
Seal the Cooktop with Foam Tape
Apply the self adhesive foam tape in one continuous
rectangle directly to the counter around the perimeter of the
cutout as shown by the dotted line in Figure 4: “Counter
Cutout – Foam Tape Placement”. Leave 1/4” (6.35mm) gap
between the foam tape and the edge of the cutout.
rectangle directly to the counter around the perimeter of the
cutout as shown by the dotted line in Figure 4: “Counter
Cutout – Foam Tape Placement”. Leave 1/4” (6.35mm) gap
between the foam tape and the edge of the cutout.
Install the Cooktop
Insert cooktop into the cutout. Attach clamps of the hold-
down brackets packaged with the cooktop to the rough-in
box. Use the washer and screws provided.
down brackets packaged with the cooktop to the rough-in
box. Use the washer and screws provided.
Adjust hold-down brackets to desired position and tighten
screws to rough-in box. Insert adjusting screw into clamp
and secure cooktop to countertop.
screws to rough-in box. Insert adjusting screw into clamp
and secure cooktop to countertop.
NOTE:
For solid surface material installations: Insert a wooden
block between the end of the screw and the bottom of the
countertop. Do not overtighten adjusting screw. Trim
excess aluminum tape around cooktop flange.
For solid surface material installations: Insert a wooden
block between the end of the screw and the bottom of the
countertop. Do not overtighten adjusting screw. Trim
excess aluminum tape around cooktop flange.
Connect Gas Supply
The gas inlet to the unit is located at the right rear of rough-
in box.
in box.
Install the pressure regulator (supplied with unit) to
manifold pipe using Teflon tape on threads of manifold
pipe. Turn to hand tighten plus 1/4 turn, not exceeding 1
turn for alignment. To prevent possible damage to the gas
pressure regulator, install it after the rough-in box is in its
permanent position. When the regulator is securely
manifold pipe using Teflon tape on threads of manifold
pipe. Turn to hand tighten plus 1/4 turn, not exceeding 1
turn for alignment. To prevent possible damage to the gas
pressure regulator, install it after the rough-in box is in its
permanent position. When the regulator is securely
Figure 3: Counter Cutout – Solid Surface Countertops
Figure 4: Counter Cutout – Foam Tape Placement
Heat Reflective Tape
Cutout shows location
of Aluminum Reflective Tape
of Aluminum Reflective Tape
Section "A - A"
A
A
1/4”
(6.35mm)
(6.35mm)
Cutout
Foam
Tape
Tape
Figure 5: Attaching Hold-Down Brackets
Figure 6: Rough-in Box Area
Rough-in Box
Foam
Tape
(Seal)
Tape
(Seal)
Adjusting
Screw
Screw
Adjusting
Screw
Screw
Clamp
Clamp
Wooden Block
(to be used with
solid surfacing
material, i.e.
Surell™ and
Corian®)
solid surfacing
material, i.e.
Surell™ and
Corian®)
Opening for Gas
Connection and
Electrical Cord
Connection and
Electrical Cord
for 30” models: 12 15/16” (313 mm)
for 36” models: 15 15/16” (389 mm)
for 36” models: 15 15/16” (389 mm)
C of Cutout
L
1”