Dacor ER30DCLPH Instrução De Instalação

Planning the Installation

IMPORTANT: Observe all governing codes and ordinances 

during planning and installation. Contact your local building 

department for further information.

Electrical Requirements 

Models ER30D and ER30DSR

It is the owner’s responsibility to ensure that the electrical 

connection of this appliance is performed by a licensed electrician. 

The electrical installation, including minimum supply wire size and 

grounding, must be in accordance with the National Electric Code 

ANSI/NFPA 70-1993* (or latest revision) and local codes and 

ordinances. A copy of this standard may be obtained from:

National Fire Protection Association 

1 Batterymarch Park 

Quincy, Massachusetts 02269-9101

• 

The correct voltage, frequency and amperage must be 

supplied to the appliance from a separate, grounded, circuit 

that is protected by a properly sized circuit breaker or time 

delay fuse. Refer to the ratings on the range rating label. If a 

fuse is utilized, fuse both sides of the line (L1 and L2).

240 Vac, 60 Hz, 30 Amp.

5.6 kW (24.2 Amp.)

The ratings above are for reference only - refer to the range 

rating label (see page 3).

• 

The wiring needs to be long enough to allow the range to be  

pulled out for service, while remaining connected.

• 

The wiring connected to the range must:
◊  Have a minimum rating of 250 Volts @ 30 Amp.
◊  Include a strain relief
◊  Be terminated by tinned leads, closed loop terminals or 

open ended spade lugs with upturned ends

◊  Connect to a junction box or receptacle installed by a 

licensed electrician

The appliance may be connected one of the following ways:
• 

Using conduit:
◊  A 4-wire conduit connected to a 4-wire junction box, or
◊  A 3-wire conduit (where local code permits) connected to 

a 3-wire junction box. 

 

 

Suggested conduit wiring color code: black, white, red 

and green.

• 

Using an appliance cord:
◊  A 4-wire appliance cord equipped with a NEMA 14-50P 

plug connected to a NEMA 14-50R receptacle, or

◊  A 3-wire appliance cord (where local code permits) 

equipped with a NEMA 10-50P plug connected to a 

NEMA 10-50R receptacle 

 

 

Appliance cord plug must be UL listed type SRD or 

SRDT. See page 14 for additional details. 

Electrical Requirements

Model ER30D-C

• 

Model ER30ED-C is a freestanding range that comes with 

a factory installed 4-wire appliance cord and NEMA 14-50P 

plug. This wiring configuration is required for freestanding 

ranges installed in Canada, although they may be used 

elsewhere, if local codes 

permit. The plug is designed 

to plug directly into a NEMA 

14-50R electrical receptacle 

installed by a licensed 

electrician according to the 

specifications below. Do not 

modify the factory wiring on 

model ER30D-C.

• 

It is the owner’s responsibility to ensure that the required 

4-wire electrical outlet compatible with the power cord is 

installed by a licensed electrician as specified below prior to 

range installation. The electrical outlet installation, including 

minimum supply wire size and grounding, must be in 

accordance with all governing codes and ordinances.

• 

The correct voltage, frequency and amperage must be 

supplied to the appliance from a separate, grounded, circuit 

that is protected by a properly sized circuit breaker or time 

delay fuse. If a fuse is utilized, fuse both sides of the line (L1 

and L2). Refer to the ratings on the range rating label.

240 Vac, 60 Hz, 30 Amp.

5.6 kW (24.2 Amp.)

The ratings above are for reference only - refer to the range 

rating label (see page 3).

Gas Supply Requirements

(all units)

• 

Check your local building codes for the proper method of 

installation. In the absence of local codes, this appliance 

should be installed in accordance with the National Fuel Gas 

Code ANSI Z223.1.

• 

Be certain that the appliance being installed is correct for 

the gas service provided (natural gas or LP gas). Also, if 

operating the range at an altitude above 4000 ft. (1219 m) 

make sure it is equipped for high altitude operation. Refer 

to the range rating label and the table on page 3 to 

determine the correct model.

• 

See the table below for gas supply pressure requirements.

• 

The regulator inlet accommodates a 3/4” gas line. The range 

ships with a 1/2” to 3/4” adapter connected to the regulator.

Natural

5

6

1/2 psi

LP

10

11

1/2 psi

The ratings above are for reference only - refer to the range rating 

label (see page 3).