Monogram ZET1FHSS Instrução De Instalação
2 B
CUTOUT FOR INSTALLATION OVER A WARMING DRAWER
NOTE: Install the oven only with specific models listed on the label located on top of the oven.
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct the required interior depth and height.
When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly
When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly
grounded receptacle must be installed. Refer to installation instructions packed with
the Warming Drawer for specific installation requirements.
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2" (5.1 cm)
Min.
Per Warming
Drawer
Requirement
B
F
G
C
A
Recommended
Cutout Location from
Floor
32
1
ø
2
” (82.6 cm)
16
1
ø
4
” (41.3 cm) Min.
Cutout –
observe all
dimensions and
requirements.
Cutout –
observe all
dimensions and
requirements.
30” (76.2 cm) Min. if both ovens are French Door
14” (35.6 cm) Min. if only one oven is French Door
14” (35.6 cm) Min. if only one oven is French Door
Center Line
Center Line
30” Models
58
1
ø
2
” (148.6 cm) if both ovens are French Door
42
1
ø
2
” (108 cm) if only one oven is French Door
These ovens
are not
approved for
stackable
installations.
H
D
E
J
J
Junction
Box
Location
(junction
box may
be located
in adjacent
cabinet)
22” (55.9
cm) Min. to
Bottom of
Junction
Box
Cutout Depth
23
1
ø
2
”
(59.7 cm) Min.
Opening
Between Inside
Walls Must be
at Least 28
1
ø
2
”
(72.4 cm) Wide
Side-by-Side Installations
Install two ovens in separate cutouts.
C
2 A
CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
both sides equally to establish the cutout width.
K
E
E
L
Dimension
Dimension Description
30” Single Oven
A
Cabinet width
30” (76.2 cm)
B
Cutout width
28
1
ø
2
” (72.4 cm) min.
28
5
ø
8
” (72.7 cm) max.
C
Cutout height
27
1
ø
4
” (69.2 cm) min.
27
5
ø
16
” (69.4 cm) max.
D
Overlap of oven over side edges of cutout
11
ø
16
” (1.75 cm)
E
Door swing depth - Allow additional clearances for
installation and oven usage
16
1
ø
4
” (41.3 cm) min.
F
Overlap of oven top of cutout
1” (2.5 cm) min.
G
Overlap of oven bottom of cutout
1
1
ø
4
” (3.2 cm)
H
Junction box location
9
1
ø
2
” (24.1 cm) max.
right side only
J
Door swing width - Allow additional clearances for
installation and oven usage
14” (35.6 cm) min.
K
Countertop or cabinet door protrusion (measure if exist)
Measure “K”
L
Gap between edge of countertop or cabinet door
to cabinet opening
If K = 0, L = 0, Otherwise
L = K + 1” (2.54 cm) min.