Liebherr HC1080 Instrução De Instalação

Risk of fire due to refrigerant.

The refrigerant contained within the appliance, R 600a, is

environmentally  friendly,  but  flammable.  Leaking  refrig-

erant can ignite.

u

Do not damage the pipes of the refrigerant circuit.

Danger of fire and damage!

u

Do  not  place  devices  that  give  off  heat,  e.g.  micro-

waves, toasters, etc. on the appliance.

Risk of damage caused by condensation

Installing  the  appliance  next  to  any  other  refrigerator  or

freezer  can  cause  condensation  or  damage  to  the  Lieb-

herr appliance.

u

Do not install this appliance next to any other refriger-

ator or freezer except another Liebherr model. Liebherr

models are designed to allow side-by-side installation.

They are equipped with a heating system to eliminate

condensation  when  refrigerators  or  freezers  are

installed side-by-side.

Risk of damage for the finished floor surface!

u

Protect the finished floor surface before you uncrate the

unit.

Danger of damage from overheating. May restrict opera-

tion.

u

Keep  ventilation  openings,  in  the  appliance  enclosure

or in the built-in structure, clear of obstruction.

Danger of tilting.

u

To avoid a hazard due to instability of the appliance, it

must be fixed in accordance with the instructions.

q If possible, have a professional install the appliance in

your kitchen cabinet unit.

q If  the  appliance  is  damaged  check  with  the  supplier

immediately before connecting it.

q The floor of the installation site must be horizontal and

level.

q Do not install the appliance in direct sunlight or next to

an oven, heater or similar heat source.

q Do not install the appliance on your own. It is better to

do this with two or more people.

q In accordance with EN 378 for each 0.28 oz (8 g) of R

600a  refrigerant  the  room  where  the  appliance  is

installed  must  have  a  volume  of  35.5  ft

3

  (1  m

3

).  If  the

installation  room  is  too  small  an  inflammable  gas/air

mixture may arise if the refrigerant circuit leaks. You will

find details of the required quantity of refrigerant on the

rating plate inside the appliance.

q If the appliance is installed in a very damp environment

condensate water may form on the outside of the appli-

ance. Always ensure good ventilation.

q The load-bearing capacity of the floor must be sufficient

for the weight of the appliance plus about 1200 pounds

(544 kg) of food weight.

q The  electrical  socket  must  assessed  precisely  to

ensure the correct position and fuse.

q Do  not  restrict  ventilation.  Sufficient  ventilation  is

required  for  the  appliance  to  operate  correctly.  The

ventilation grid fitted at the factory guarantees an effec-

tive  ventilation  gap  on  the  appliance  of  31  in.

2

(200  cm

2

).  If  you  replace  the  ventilation  grid  with  a

fascia, this must have at least the same size or larger

ventilation gap as the manufacturer's ventilation grid.

u

Note down the type (model, number), appliance name,

appliance  or  serial  number,  date  of  purchase  and

manufacturer's address in the place provided for this in

the Use & Care Manual.

u

Remove  all  materials  that  could  prevent  it  from  being

installed properly or prevent proper ventilation from the

back or the side panels of the appliance.

u

Remove  the  red  transport

safety device. Close off any

holes  that  have  been

revealed with plugs (60).

u

Remove protective films, adhesive tapes and transport

safety devices, etc.

u

Clean  the  appliance  (see  operating  instructions,

"Cleaning the appliance" section).