Faber CRIS24SS Ficha De Características
Cut-Out
Dimensional Diagrams
Rev.07/11
WARNING! Product specifications are subject to change without notification. Consult the installation instructions
before you begin installing this rangehood.
before you begin installing this rangehood.
Make your ductrun as straight and
short as possible. The ductrun
should not exceed 35 equivalent feet
if ducted with the required minimum
of 6” round duct. Count 45º angles
as 3 feet, 90º elbows as 5 feet, and
90º flat elbows as 12 feet.
short as possible. The ductrun
should not exceed 35 equivalent feet
if ducted with the required minimum
of 6” round duct. Count 45º angles
as 3 feet, 90º elbows as 5 feet, and
90º flat elbows as 12 feet.
For best results, use no more
than three 90° elbows. Make sure
that there is a minimum of 24”
of straight duct between elbows
if more than one is used. Do not
install two elbows together. If you
must elbow right away, do it as
far away from the hood’s exhaust
opening as possible.
than three 90° elbows. Make sure
that there is a minimum of 24”
of straight duct between elbows
if more than one is used. Do not
install two elbows together. If you
must elbow right away, do it as
far away from the hood’s exhaust
opening as possible.
Pre-Planning Your Ductwork
-
Important: Consult the installation instructions before you begin installing this rangehood.
Recirculating Installations
Some ductwork must
be installed to exhaust
the rangehood back
into the kitchen, either
at the top of the
cabinet or at the face
of the soffit. A plastic
vent grate supplied
with the rangehood
can be used to cover
the duct opening. This
duct work must not
terminate into a dead
air space.
be installed to exhaust
the rangehood back
into the kitchen, either
at the top of the
cabinet or at the face
of the soffit. A plastic
vent grate supplied
with the rangehood
can be used to cover
the duct opening. This
duct work must not
terminate into a dead
air space.
Front View
For installations where ductwork to the outside of your home is impossible or highly impractical
Charcoal Filters, which attach to the blower assembly, absorb smoke and odors.
Charcoal Filters, which attach to the blower assembly, absorb smoke and odors.
cabinet
ceiling
6” round
duct
hood
cabinet
ceiling
6” round
duct
hood
soffit
vent grate
vent grate
Pre-Planning Your Installation
-
Important: Consult the installation instructions before you begin installing
this rangehood. The recommended height to install this hood off the cooktop is a minimum of 24” and a maximum of 30”
for maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.
for maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.
EN
77
DIMENSIONS and MAIN PARTS
Components
Ref. Q.ty Product Components
1
1
1 Hood Body, complete with: Controls, Light, Blower, Fil-
ters
8
1 Directional Air Outlet grille
10
1 Damper
20
1 Closing element
Ref. Q.ty Installation Components
12a
12a
4 Screws 3/16î x 1î 3/4
12e
2 Screws 1/8î x 6/16î
Q.ty Documentation
1 Instruction Manual
�
���
���
�
��
��
EN
88
INSTALLATION
Drilling the Support surface and Fitting the Hood
SCREW FITTING
• The hood support surface must be 8” 11/16 above the bottom
surface of the wall units.
• Drill the support with a ø 3/16”drill bit, using the drilling tem-
plate provided.
• Cut a hole ø 6”in size on the support surface, using the drilling
template provided.
• Fix using the 4 screws 12a provided.
����
����
����
���
SNAP-ON FITTING
• The hood can be installed either directly on the bottom surface
of the wall units using snap-on side supports.
• Cut a fitted opening in the bottom surface of the wall unit, as
shown.
• Insert the hood until the side supports snap into place.
• Lock in position by tightening the screws Vf from underneath
the hood.
�����
��������
��������������������
��
CLOSING ELEMENT
• The space between the edge of the hood and the rear wall can
be closed by applying the element 20 provided, using the
screws supplied for this purpose.
��