Faber SYNT30SS300 Ficha De Características
1” min
16
3/8”
max
22”
9
1/2”
36”
x
also consult cooktop
manufacturer's recommendation
upper
chimney
chimney
lower
chimney
chimney
canopy
x = distance from hood to cooktop
(varies depending on installation)
min - 24”, suggested max - 30”
cabinet base
19
1/4”
min & max ceiling height examples
x = 30"
min
8'
2 1/2"
max
9'
5 7/8"
x = 28"
min
8'
1/2"
max
9'
3 7/8"
x = 26"
min
7'
10 1/2"
max
9'
1 7/8"
x = 24"
min
7'
8 1/2"
max
8'
11 7/8"
Rev. 07/11
Dimensional Diagrams & Electrical Knockouts
For shorter ceilings, have
the chimney cover(s) cut
at a sheet metal shop.
For higher ceiling instal-
lations, the High Ceiling
Chimney Kit includes a
new 40” upper chimney
which would replace the
16 3/8” upper chimney
that came with the hood.
that came with the hood.
The Synthesis chim-
neys are adjustable
and designed to meet
varying ceiling heights.
The chimneys can be
adjusted for ceilings be-
tween 7’ 8 1/2” and 9’ 5
7/8” depending on the
distance between the
bottom of the hood and
the cooktop (distance x
in left diagram).
neys are adjustable
and designed to meet
varying ceiling heights.
The chimneys can be
adjusted for ceilings be-
tween 7’ 8 1/2” and 9’ 5
7/8” depending on the
distance between the
bottom of the hood and
the cooktop (distance x
in left diagram).
36” Model
30” Model
30” or 35 3/8”
* it is highly recommended that
professional style cooking al-
ways be vented to the outside.
professional style cooking al-
ways be vented to the outside.
WARNING!
Product specifications are subject to change without notification. Consult the installation instructions before you begin installing this rangehood.
Ductless Installations*
For installations where duct-
work is impossible or highly
impractical, a Ductless
Conversion Kit is available.
A charcoal filter, which at-
taches under the blower as-
sembly, absorbs smoke and
odors. A ductless diverter
assembly directs the air out
to a lower chimney with vent
grates cut into the sides.
work is impossible or highly
impractical, a Ductless
Conversion Kit is available.
A charcoal filter, which at-
taches under the blower as-
sembly, absorbs smoke and
odors. A ductless diverter
assembly directs the air out
to a lower chimney with vent
grates cut into the sides.
Make your ductrun as straight and short as pos-
sible. The ductrun should not exceed 35 equiva-
lent feet if ducted with the required minimum of 6”
round duct. Count 45º angles as 3 feet, 90º elbows
as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° el-
bows. Make sure that there is a minimum of 24”
of straight duct between elbows if more than
one is used. Do not install two elbows together.
If you must elbow right away, do it as far away
from the hood’s exhaust opening as possible.
sible. The ductrun should not exceed 35 equiva-
lent feet if ducted with the required minimum of 6”
round duct. Count 45º angles as 3 feet, 90º elbows
as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° el-
bows. Make sure that there is a minimum of 24”
of straight duct between elbows if more than
one is used. Do not install two elbows together.
If you must elbow right away, do it as far away
from the hood’s exhaust opening as possible.
Pre-Planning Your Installation -
Important: Consult the installation instructions before you begin installing this rangehood.
Ducted
Ductless