Vigo Industries VGT54A Guia De Especificação
3
To ensure that your installation project goes smoothly, please review these
instructions before proceeding.
Your new lavatory is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals.
cleaners, steel wool and harsh chemicals.
MAINTENANCE
ASSEMBLY
REQUIRED TOOLS
Plumber's putty or Caulk
Caulking Gun
Caulking Gun
Tape Measure
SAFETY TIPS
Observe all local plumbing and building codes.
Risk of personal injury or product damage. Handle with care. Glass can break or
chip if the product is handled carelessly.
Prior to installation, unpack the new lavatory and inspect it for damage. Return the
lavatory to its protective carton until you are ready to install it.
Risk of personal injury or product damage. Handle with care. Glass can break or
chip if the product is handled carelessly.
Prior to installation, unpack the new lavatory and inspect it for damage. Return the
lavatory to its protective carton until you are ready to install it.
IMPORTANT POINTS
1. Installation must be done by a qualified, licensed plumber . The contractor must
perform a dry fit prior to drilling holes in the counter top for the sink.
perform a dry fit prior to drilling holes in the counter top for the sink.
3. All Vigo vessel bowls are hand made. You may expect variations in color,
texture and bowl symmetry. If you notice any obvious variation or defects you
should contact your retailer immediately.
4. Vessel sinks are extremely durable and can withstand a temperature change
texture and bowl symmetry. If you notice any obvious variation or defects you
should contact your retailer immediately.
4. Vessel sinks are extremely durable and can withstand a temperature change
5. Though resistant to breakage, vessel sinks can break or chip when a heavy
object falls in or on them.
object falls in or on them.
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
PACKAGE CONTENTS
ONLY THE SINK IS PROVIDED
Make sure to use the intended style drain / pop-up. The Vigo style vessel bowl
does not have an overflow. Therefore the drain / pop-up needs to
correspond appropriately.
correspond appropriately.
LAVATORY
Turn off the water supply. This is done by closing the two shut-off valves
located under the lavatory. If there are no shut-off valves leading to the lavatory,
you must turn off the water at the main valve. This is usually located in the
basement, garage or near the foundation on the outside of the house. It may
also be near the water meter. Check to be sure the water is off by turning on
the faucet where you are working until the water stops flowing. If you have shut
off the main valve in a two-story house or greater, you should open the kitchen
faucet and another faucet on the same level. Water will then drain from the
entire line. This will help avoid spills. Be sure and close the faucets before you
turn on the main valve again. Disconnect the drain pipes. Take off as many
sections as possible between the lavatory and the wall or floor to facilitate
located under the lavatory. If there are no shut-off valves leading to the lavatory,
you must turn off the water at the main valve. This is usually located in the
basement, garage or near the foundation on the outside of the house. It may
also be near the water meter. Check to be sure the water is off by turning on
the faucet where you are working until the water stops flowing. If you have shut
off the main valve in a two-story house or greater, you should open the kitchen
faucet and another faucet on the same level. Water will then drain from the
entire line. This will help avoid spills. Be sure and close the faucets before you
turn on the main valve again. Disconnect the drain pipes. Take off as many
sections as possible between the lavatory and the wall or floor to facilitate
removal. Place a basin under the work area to catch any water that may still be
in the drain.
in the drain.
REMOVING YOUR OLD LAVATORY
NOT PROVIDED
TAIL PIECE
DRAIN NUT
TO DRAIN
WASHER
DRAIN ASSEMBLY
SOFT WHITE WASHER
STAND
RUBBER STAND WASHER
POP UP TOP
INTERNAL BRASS PIECE (POP UP MECHANISM)
1. Please inspect your working surface, making sure it is level and clean.
2. Determine the layout for the sink you desire. It is important to fully "dry" position
the sink with your faucet purchase on the countertop. Things to include, but are not
limited to;
the sink with your faucet purchase on the countertop. Things to include, but are not
limited to;
desired position.
4. The sink can be mounted to the countertop with or without a stand. It is highly
recommended that the customer utilize the stand. This will allow for proper
cleaning around the exterior of the bowl and will make sure that there is no direct
contact between your bowl and desired countertop. The stand is an optional
purchase and is not included in with the purchase of the vessel bowl. Note: The
stand comes as a free accessory with a Vigo style pop up. If you decide not to
purchase the Vigo style pop up, the stand can be purchased through the Vigo
cleaning around the exterior of the bowl and will make sure that there is no direct
contact between your bowl and desired countertop. The stand is an optional
purchase and is not included in with the purchase of the vessel bowl. Note: The
stand comes as a free accessory with a Vigo style pop up. If you decide not to
purchase the Vigo style pop up, the stand can be purchased through the Vigo
technical support department.
5. If a stand is not purchased it is advised to apply a bead of caulk between the
bottom of the sink and the countertop. This will prevent movement and ease the
leveling process.
bottom of the sink and the countertop. This will prevent movement and ease the
leveling process.
DO NOT OVER TIGHTEN THE DRAIN
!
STAND
RUBBER WASHER
STAND
BLACK RUBBER WASHER
STAND
POP UP DRAIN
RUBBER WASHER
TAIL PIECE
DRAIN NUT
SOFT WHITE WASHER
STAND
RUBBER STAND WASHER
POP UP DRAIN TOP
RUBBER WASHER
SINK
BLACK RUBBER WASHER
COUNTERTOP
TAIL PIECE NUT
COUNTERTOP
INTERNAL BRASS PIECE
(POP UP MECHANISM)
(POP UP MECHANISM)
TOP VIEW
BOTTOM VIEW
(with stand installed)
WHITE PLASTIC WASHER
WHITE PLASTIC WASHER