Dacor DR30DLP Instrução De Instalação
16
Installation Instructions
Verifying Proper Operation
WARNING
Before operating the range, read the accompanying use and
•
care manual completely.
Make sure that power to the range is turned off at the circuit
Make sure that power to the range is turned off at the circuit
•
breaker or fuse box and that the gas is turned off at the gas
supply valve before proceeding.
The cooktop must be properly grounded at all times when
The cooktop must be properly grounded at all times when
•
electrical power is applied.
Before beginning the test procedure, ensure that all cooktop
1.
control valves are in the
OFF position, and all burner rings,
burner caps and grates are properly positioned on the spill
tray. Remove any packaging from inside the oven.
Turn on the gas supply at the shut-off valve.
Turn on the gas supply at the shut-off valve.
2.
Plug in the appliance cord, if applicable. Turn on power to the
3.
range at the circuit breaker or fuse box.
Perform the following ignition test for all of the burners:
Perform the following ignition test for all of the burners:
4.
Push in and turn one
◊
of the control knobs
counterclockwise to the
HIGH position. Only the
igniter for the selected
burner will spark. It may take up to four seconds for the
gas to ignite, at which time the igniter will stop sparking.
If ignition does not occur within four seconds, turn the
knob to the
OFF position, wait for at least five minutes to
allow any gas to dissipate, then repeat the test.
Once the burner lights, the control knob can be rotated
Once the burner lights, the control knob can be rotated
◊
counterclockwise from
HIGH to LOW to adjust the flame
height progressively.
When the unit is installed
When the unit is installed
◊
properly, the flame will be
steady. It will also have a
sharp, blue inner cone that
will vary in length proportional
to the burner size. The flame
will be reduced by the Smart
Flame™ feature under the
grate fingers to increase grate
life.
Set the clock according to the use
5.
and care manual.
Press the
Press the
6.
BAKE key on the control panel. The default bake
temperature should appear on the display.
Enter the temperature of 350°F on the keypad.
Enter the temperature of 350°F on the keypad.
7.
Press
8.
START. The display should show the
BAKE symbol and the preheating temperature.
After approximately three (3) minutes, the oven
After approximately three (3) minutes, the oven
9.
should begin to heat. Press the
CANCEL-
SECURE key to stop the oven heating process.
NOTES:
If either the oven or cooktop does not operate properly,
follow these troubleshooting steps:
Verify that power and gas are supplied to the range.
1.
Check the electrical connections and gas supply to ensure
2.
that the installation has been completed correctly.
Repeat the bake test or burner ignition test.
3.
If the appliance still does not work, contact Dacor Distinctive
4.
Service at (877) 337-3226. Do not attempt to repair the
appliance yourself. Have the model and serial numbers
available when you call. See page 3 for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
Installation Checklist
WARNING
To ensure a safe and proper installation, the following checklist
should be completed by the installer to ensure that no part of
the installation has been overlooked.
Has the plastic coating been peeled off of the outside of the
□
range? Have all packaging materials been removed from
inside the oven?
Are all leveling legs extended down to make contact with the
Are all leveling legs extended down to make contact with the
□
floor? Is the unit level? See page 7.
Is the range secured in place with the provided anti-tip
Is the range secured in place with the provided anti-tip
□
bracket and foot according to these instructions? See page 9.
Is the range wired and grounded according to these
Is the range wired and grounded according to these
□
instructions and in accordance with all applicable electrical
codes? Has the electrical access cover been replaced? See
Pages 4 and 8 to 13.
Has the gas supply inlet pressure been measured to ensure
Has the gas supply inlet pressure been measured to ensure
□
that it does not exceed the maximums stated in these
instructions? See page 4.
Is the range connected to the gas supply according to these
Is the range connected to the gas supply according to these
□
instructions and in accordance with all applicable codes? See
page 13.
Did the installer check the gas supply for leaks?
Did the installer check the gas supply for leaks?
□
Is the oven door properly installed according to these
□
instructions? See page 14.
Have the burner knobs been installed in the proper positions?
Have the burner knobs been installed in the proper positions?
□
See page 14.
Are the burners and grates properly installed according to
Are the burners and grates properly installed according to
□
these instructions? See page 15.
Has proper operation been verified?
Has proper operation been verified?
□
Has the warranty been activated on-line or the warranty card
□
been filled out completely and mailed?
OFF
HIGH
LOW
Normal Flame
BAKE
1
2