Alpine INE-W940 Manual Do Proprietário
34
-EN
Sound Setup Operation
1
Touch [Setup] icon of Top banner.
The Setup main screen is displayed.
2
Touch [Sound Menu].
The Sound Menu screen appears.
3
Select the desired item.
Setting items: Car Specific Sound Setup / Media Xpander /
Factory's EQ / Balance/Fader/Sub.W /
TCR (Time Correction) / X-OVER / Parametric EQ /
Other / Defeat
TCR (Time Correction) / X-OVER / Parametric EQ /
Other / Defeat
4
Touch [
] or [
] etc., to change its setting.
• When the pop-up window for setup is displayed, touch [
] to
close the window after setting.
5
Touch [
] to return to the previous screen.
• Immediately after changing the Sound Setup (while the system is
writing data automatically) do not turn the ignition key to OFF.
Otherwise, the settings may not be changed.
Otherwise, the settings may not be changed.
Car Specific Sound Setup
[Car Specific Sound Setup] is selected on the Sound setup menu in
step 3. Refer to “Sound Setup Operation” (page 34).
You can set and reproduce the best audio environment for the
environment in your car.
step 3. Refer to “Sound Setup Operation” (page 34).
You can set and reproduce the best audio environment for the
environment in your car.
1
Touch the relevant Vehicle type.
2
Touch the position of the driver’s seat.
3
Touch the size of the front speaker.
4
Select whether or not there is a tweeter.
5
Select the installation position of the rear speaker.
If you select “No rear speaker,” you cannot adjust the rear
speaker in Fader/Time Correction/X-OVER in sound setup.
speaker in Fader/Time Correction/X-OVER in sound setup.
6
Select whether or not there is a subwoofer.
If you select “No,” you cannot adjust the subwoofer level/
subwoofer phase in sound setup.
subwoofer phase in sound setup.
7
Select the material of the car seats.
The settings confirmation screen is displayed.
• If the car seats are made of both leather and fabric, select [Half
• If the car seats are made of both leather and fabric, select [Half
leather].
8
Check the settings and touch [OK].
• If Preset3 was already saved for Time Correction/X-OVER/
Parametric EQ, the data will be overwritten.
• The Car Specific Sound settings are reflected in the following Audio
Setup items.
Setting the MX (Media Xpander)
Adjusting the Parametric Equalizer Curve (Parametric EQ)
Adjusting the Time Correction (TCR)
Setting the MX (Media Xpander)
Adjusting the Parametric Equalizer Curve (Parametric EQ)
Adjusting the Time Correction (TCR)
Sound Setup
To display the Sound Setup Menu screen:
Your vehicle must be parked with the ignition key in the ACC or
ON position. To do this, follow the procedures below.
Your vehicle must be parked with the ignition key in the ACC or
ON position. To do this, follow the procedures below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the Sound mode operation has been
released. Engaging the parking brake can reactivate the Sound
Setup Menu, as long as the car’s ignition has not been turned off.
It is not necessary to repeat the above procedure
(1 through 3) of “To display the Sound mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Sound mode screen.”
released. Engaging the parking brake can reactivate the Sound
Setup Menu, as long as the car’s ignition has not been turned off.
It is not necessary to repeat the above procedure
(1 through 3) of “To display the Sound mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Sound mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of Sound Setup. Refer to each section for details.
“Setting item” of Sound Setup. Refer to each section for details.