Alpine IVE-W530 Manual Do Proprietário
31
-EN
Source Setup Operation
1
Touch [
] on the main screen.
The SETUP selection screen is displayed.
2
Touch the title bar of Source Setup.
The SOURCE SETUP screen appears.
3
Touch the title bar of your desired Setup mode.
DVD Setup*
1
/ Radio Setup / BLUETOOTH Setup*
2
*
1
Refer to “DVD Setup” on page 29.
*
2
Displayed when “BLUETOOTH IN” is set to other than “OFF”
(page 38).
(page 38).
4
Touch [
], [
] or the title bar, etc. of the desired
item to change its setting.
Radio Setup:
FM Level
BLUETOOTH Setup:
Paired Devices / Device Search / Clear Device / Service Provider /
Visible Mode / Auto Answer / Speaker Select / MIC Input /
Visible Mode / Auto Answer / Speaker Select / MIC Input /
Firmware Version / Firmware Update / BT Menu Language /
Shortcut Memory
Shortcut Memory
• For BLUETOOTH Setup details, refer to “BLUETOOTH Setup”
5
Touch [
] to return to the previous screen.
“Radio Setup” is selected on the source setup main menu in step 3.
Adjusting Source Signal Levels
If the difference in volume level between the CD and FM radio is
too great, adjust the FM signal level as follows.
too great, adjust the FM signal level as follows.
Setting item: FM Level
Setting contents: Low / High
Display Setup Operation
1
Touch [
] on the main screen.
The SETUP selection screen is displayed.
2
Touch the title bar of Display Setup.
The Display Setup screen appears.
3
Touch [
] or [
] etc., of the desired item to change
its setting.
Setting items:
Visual EQ*
1
/ Dimmer / Screen Dimmer Level*
2
/ Function Guide
Fade / Base Color / Screen Alignment / Visual Key
*
1
For details, refer to “Visual EQ Setting Operation” on page 33.
*
2
Not displayed when “Dimmer” is set to “OFF”.
4
Touch [
] to return to the previous screen.
• Touching [Exit] will turn off the Display Setup screen, and return to
previous main screen.
• Immediately after changing the settings of Display Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF.
(engine key) to OFF.
Otherwise, the settings may not be changed.
Source Setup
To display the Source Setup mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the Source mode operation has been
released. Engaging the parking brake can reactivate the Source
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the Source mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Source mode screen.”
released. Engaging the parking brake can reactivate the Source
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the Source mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Source mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of Radio Setup. Refer to each section for details.
“Setting item” of Radio Setup. Refer to each section for details.
Radio Setup
Display Setup
To display the Display mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the Display mode operation has been
released. Engaging the parking brake can reactivate the Display
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the Display mode screen”.
Each time the ignition is turned OFF, perform the procedure of “To
display the Display mode screen”.
released. Engaging the parking brake can reactivate the Display
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the Display mode screen”.
Each time the ignition is turned OFF, perform the procedure of “To
display the Display mode screen”.
The following steps 1 to 4 are common operations to each
“Setting item” of Display Setup. Refer to each section for
details.
“Setting item” of Display Setup. Refer to each section for
details.