Alpine IVE-W530 Manual Do Proprietário
36
-EN
System Setup Operation
1
Touch [
] on the main screen.
The SETUP selection screen is displayed.
2
Touch the title bar of System Setup.
The System Setup screen appears.
3
Touch [
] or [
] of the desired item to change its
setting.
Setting items:
Camera IN / Nav. IN / Nav. Mix* / AUX1 IN / AUX2 IN / AUX Front /
AUX Out / BLUETOOTH IN / Illumi Color
AUX Out / BLUETOOTH IN / Illumi Color
* When ON is set in “Setting the Navigation Mode” (page 37), the item
is displayed.
4
Touch [
] to return to the previous screen.
• Touching [Exit] will turn off the System Setup screen, and return to
previous main screen.
• Immediately after changing the settings of System Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF.
(engine key) to OFF.
Otherwise, the settings may not be changed.
With an optional rear camera connected, rear view video is output to the
monitor.
monitor.
Setting item: Camera IN
Setting contents: OFF / ON
• By shifting to reverse (R), the rear pictures are output.
This function is effective when the reverse wire is properly connected.
After setting this item to ON, touch the title bar of Camera IN, the
following further setting items can be adjusted.
following further setting items can be adjusted.
Setting the Rear Camera Signal Input
The video input signal type can be chosen.
Further Setting item: Camera Signal
Setting contents: NTSC/PAL / Auto
Setting contents: NTSC/PAL / Auto
• When set to Auto, unstable display may occur while playing back
certain black and white video signal. In this case, select NTSC or
PAL mode manually.
PAL mode manually.
Rear camera guide line display setting
You can set whether the rear camera guide line is displayed or
not.
not.
Further Setting item: Guide Line
Setting contents: OFF / ON
Setting contents: OFF / ON
Adjusting the Rear Camera Guide line
You can adjust the rear camera guide line position.
Further Setting item: Guide Line Adjustment
System Setup
To display the System mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the System mode operation has been
released. Engaging the parking brake can reactivate the System
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the System mode screen”.
Each time the ignition is turned OFF, perform the procedure of “To
display the System mode screen”.
released. Engaging the parking brake can reactivate the System
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the System mode screen”.
Each time the ignition is turned OFF, perform the procedure of “To
display the System mode screen”.
The following steps 1 to 4 are common operations to each
“Setting item” of System Setup. Refer to each section for details.
“Setting item” of System Setup. Refer to each section for details.
Setting the Rear Camera Input
OFF:
The Camera mode is not displayed in the mode
switching screen.
switching screen.
ON:
Use when the optional rearview camera is
connected to the CAMERA Input Connector.
connected to the CAMERA Input Connector.
NTSC/PAL: Choose the video input signal type manually.
Auto:
The suitable video input signal type will be
automatically chosen between NTSC and PAL.
automatically chosen between NTSC and PAL.