Koolspace koolR Magnum Wine Cellar Cooling Unit - 900 Cu. Ft. Manual Do Produto
CENTER
WARM SIDE
CENTER
WARM SIDE
1
2
3
4
5
6
WARM
SIDE
COOL
SIDE
!
!
FRAME
!
ELBOW
TUBE
CONT
AINER
SILICONE CAULKING
PLYWOOD
FLOOR VAPOR
BARRIER
INSULATION
(MIN. R-20)
SEAL ALL
JOINTS
ODORLESS
WATERPROOF
PAINT
D
RY
W
ALL
VAP
OR BARRIER
INSULATION
MINIMUM R-20
VAP
OR BARRIER
Min. 6’
Min. 2’
clear
space
Min.5”
D
RY
W
ALL
INSULATED
DOOR
WITH
AIRTIGHT
SEAL
SUB-FLOOR
(STUD LUMBER)
ALTERNATIVE
WALL CUTOUT
RECOMMENDED
OVER THE DOOR
CUTOUT
Min
10”
1
2
3
4
5
6
LOCATION:
Appliance is for indoor use only. Never vent into a laun-
dry closet or similar room which traps warm air. Unit
must vent to an adjacent interior ventilated space close
to the ceiling. Exhaust air must not be obstructed in any
way.
dry closet or similar room which traps warm air. Unit
must vent to an adjacent interior ventilated space close
to the ceiling. Exhaust air must not be obstructed in any
way.
TEMPERATURES:
Select a suitable area, sized to model’s capacity, where
ambient temperature will not exceed the desired storage
temperature by more than 25ºF (14ºC). The temperature
of the air where the unit vents its warm air must be at
least 65º and never exceed 80ºF with 70% R.H. Lower
set temperature from default 57ºF (14ºC) only if ambient
condition allows.
ambient temperature will not exceed the desired storage
temperature by more than 25ºF (14ºC). The temperature
of the air where the unit vents its warm air must be at
least 65º and never exceed 80ºF with 70% R.H. Lower
set temperature from default 57ºF (14ºC) only if ambient
condition allows.
Room temperature range: 52º-64º (11ºC-18ºC)
INSULATION:
Install unit where ALL surfaces (walls, floor and ceiling)
are insulated to R-20 and protected by vapor barrier on
are insulated to R-20 and protected by vapor barrier on
both sides. Uninsulated concrete floors will radiate heat
and humidity during summer months, forcing the unit to
and humidity during summer months, forcing the unit to
work inefficiently. All floors must be INSULATED! Use an
insulated door with weather seal.
insulated door with weather seal.
POWER:
Outlet (on cool side) power must be a dedicated sepa-
rately fused grounded 15-Amp 115 Volt line within reach
of supplied power cord (Europe; 10-Amp 220 Volt). Line
rately fused grounded 15-Amp 115 Volt line within reach
of supplied power cord (Europe; 10-Amp 220 Volt). Line
must not be shared. Do not use extension cords.
Electronics must be protected against sudden power
surges. Use a quality surge protector.
surges. Use a quality surge protector.
SPECIAL NOTE:
This unit is constructed for installation in walls up to 6
1/2” inches thick. If you install it in a thicker wall you will
have to cut out an area around the air vents on cool side
1/2” inches thick. If you install it in a thicker wall you will
have to cut out an area around the air vents on cool side
in order not to block airflow. order longer screws at www.
koolspace.com.
koolspace.com.
READ BEFORE YOU START
Center pattern to door frame.
•
Trace pattern.
•
Flip pattern and repeat for cool side.
•
Cut out drywall, warm and cool side.
•
Cut out Stud level to drywall cutout.
•
• Get help to insert cooling unit through hole.
Guide cord, do not damage drywall!
•
Slide over frame on cool side, guide cord through
•
frame side notch.
Screw in cooling unit to frame.
Screw in cooling unit to frame.
•
Place grill on unit.
•
WATER DRAIN
Add tube to elbow.
•
Insert elbow to cooling unit.
•
NOTE: Excess condensation is caused by extreme conditions.
This is not required if your room is properly insulated.
This is not required if your room is properly insulated.
ALTERNATE WALL CUTOUT
Level pattern, trace both warm and cool side.
•
Cut out drywall.
•
Screw in cooling unit to frame.
•
MARK SLITS