American Standard 2705.118W Manual Do Utilizador
ELLISSE BUILT-IN™ WHIRLPOOL
HIGH GLOSS ACRYLIC
ELLISSE BUILT-IN WHIRLPOOL
Whirlpool Featuring System I:
❏
2703.118W End Mount Pump, Right Hand Outlet
❏
2703.218W End Mount Pump, Left Hand Outlet
❏
2705.118W Front Mount Pump, Right Hand Outlet
❏
2705.218W Front Mount Pump, Left Hand Outlet
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Dual, molded-in arm rests
• Integral 3-sided tiling/water retention flange
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord and plug
• Six multi-directional and flow-adjustable jets
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Dual, molded-in arm rests
• Integral 3-sided tiling/water retention flange
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord and plug
• Six multi-directional and flow-adjustable jets
including:
- Two foot jets
- Two body massage jets
- Two back-rest jets
- Two body massage jets
- Two back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
StayClean™ Whirlpool Featuring System I:
❏
2703.118WC End Mount Pump, Right Hand outlet
❏
2703.218WC End Mount Pump, Left Hand outlet
❏
2705.118WC Front Mount Pump, Right Hand outlet
❏
2705.218WC Front Mount Pump, Left Hand outlet
• Same as above except with the StayClean™
• Same as above except with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
AlphaSan®
Nominal Dimensions: 1524 x 813 x 546mm
(60” x 32” x 21-1/2")
(60” x 32” x 21-1/2")
© 2003 American Standard Inc.
BV-17
NOTE:
Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 3/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specified - Required:
❏
Color:
❏
Bath Filler: (specify finish)
❏
Bath Drain: 1583.470 (specify finish)
❏
Grab Bar Kit: 9827-200-two per kit (specify finish)
To Be Specified - Optional:
❏
Safe-T-Heater*: 9075.120
❏
Ellisse Apron: 9160.2705(specify color)
❏
Jet Trim Ring Kit: 9860.200-two per kit (specify
finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
temperature during operation. It will not heat cold water to
desired bathing temperature.