Phoenix Gold SD800.5 Manual Do Utilizador

© 2011 Phoenix Gold • www.phoenixgold.com  

Amplifier Owner’s Manual

RMS Power 14.4Vdc ≤ 1% THD  

        200 x 1 @ 4 ohm 

 

        300 x 1 @ 2 ohm

Dynamic Power 14.4Vdc >1% THD 

        300 x 1 @ 4 ohm

 

        400 x 1 @ 2 ohm

Recommended Fuse Size:  

        30 amp

Power/Ground Wire Size:  

        8 Gauge

Dimensions (Includes Mounting Feet):           7.24” L x 6.93” W x 2.0” H

 

        184mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        7.36” L x 6.93” W x 2.0” H

 

        187mm L x 176mm W x 51mm H 

RMS Power 14.4Vdc ≤1% THD 

75 x 4 @ 4 ohm Stereo

 

125 x 4 @ 2 ohm Stereo

 

250 x 2 @ 4 ohm Bridged

Dynamic Power 14.4Vdc >1% THD 

90 x 4 @ 4 ohm Stereo

 

150 x 4 @ 2 ohm Stereo

 

300 x 2 @ 4 ohm Bridged

Recommended Fuse Size: 

50 amp

Power/Ground Wire Size: 

8 Gauge

Dimensions (Includes Mounting Feet):           10.0” L x 6.93” W x 2.0” H

 

        254mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        10.63” L x 6.93” W x 2.0” H

 

        270mm L x 176mm W x 51mm H 

 

INPUT

Connect preamp signal cables from the head unit to these terminals.

CROSSOVER FREQUENCY

Controls the lowpass crossover point for the speaker outputs. 

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz. 

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control. This allows 

up to 20dB of volume adjustment.  This is not a bass boost, it controls the 

level of the low pass signal. 

NOTE: This control is not compatible with the Phoenix Gold LPL44 level 

control.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

SUBSONIC CROSSOVER FREQUENCY

Controls the highpass crossover point for the speaker outputs to eliminate 

extreme low frequencies. 

+12V 

This must be connected to the fused positive terminal (+12V) of the car’s 

battery. The fuse must be located within 18 inches of the battery. 

REMOTE 

This must be connected to switched +12V, usually a trigger wire coming 

from the head unit or ignition. 

GROUND

 

This must be connected to the negative terminal of the car’s battery or 

bolted to a clean, unpainted part of the chassis of the vehicle.

SPEAKER OUTPUTS

Used to connect the amplifier to speakers. SD600.1 minimum impedance 

is 1 ohm. SD300.1 minimum impedance is 2 ohm. 

RMS Power 14.4Vdc ≤1% THD 

75 x 4 @ 4 ohm Stereo

 

125 x 4 @ 2 ohm Stereo

 

250 x 2 @ 4 ohm Bridged

 

 

plus

 

200 x 1 @ 4 ohm

 

300 x 1 @ 2 ohm

 

Dynamic Power 14.4Vdc >1% THD 

90 x 4 @ 4 ohm Stereo

 

150 x 4 @ 2 ohm Stereo

 

300 x 2 @ 4 ohm Bridged

 

 

plus

 

300 x 1 @ 4 ohm

 

400 x 1 @ 2 ohm

Recommended Fuse Size: 

60 amp

Power/Ground Wire Size: 

4 Gauge

Dimensions (Includes Mounting Feet):           11.57” L x 6.93” W x 2.0” H

 

        294mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        12.2” L x 6.93” W x 2.0” H

 

        310mm L x 176mm W x 51mm H

NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD amplifiers.

RMS Power 14.4Vdc ≤ 1% THD  

        400 x 1 @ 2 ohm 

 

        600 x 1 @ 1 ohm

Dynamic Power 14.4Vdc >1% THD 

        600 x 1 @ 2 ohm

 

        800 x 1 @ 1 ohm

Recommended Fuse Size:  

        60 amp

Power/Ground Wire Size:  

        4 Gauge

Dimensions (Includes Mounting Feet):           10.0” L x 6.93” W x 2.0” H

 

        254mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        10.12” L x 6.93” W x 2.0” H

 

        257mm L x 176mm W x 51mm H